低碳中锰Q690F高强韧中厚板生产技术

doi:10.12068/j.issn.1005-3026.2019.04.06

东北大学学报:自然科学版 ›› 2019, Vol. 40 ›› Issue (4): 483-487.DOI: 10.12068/j.issn.1005-3026.2019.04.06

低碳中锰Q690F高强韧中厚板生产技术

齐祥羽¹，朱晓雷²，胡军¹，杜林秀¹

(1. 东北大学轧制技术及连轧自动化国家重点实验室，辽宁沈阳110819; 2. 鞍钢集团钢铁研究院海洋装备用金属材料及其应用国家重点实验室，辽宁鞍山114009)

收稿日期:2018-01-30 修回日期:2018-01-30 出版日期:2019-04-15 发布日期:2019-04-26
通讯作者: 齐祥羽
作者简介:齐祥羽(1988-)，男，吉林白山人，东北大学博士研究生; 杜林秀(1962-)，男，辽宁本溪人，东北大学教授，博士生导师.
基金资助:
国家高技术研究发展计划项目(2015AA03A501).

Production Technology of Low-C Medium-Mn Q690F High Strength and Toughness Mid-Thick Steel Plate

QI Xiang-yu¹， ZHU Xiao-lei²， HU Jun¹， DU Lin-xiu¹

1. State Key Laboratory of Rolling and Automation， Northeastern University， Shenyang 110819， China; 2. State Key Laboratory of Metal Materials for Marine Equipment and Application， Iron & Steel Research Institutes of Ansteel Group Corporation， Anshan 114009，China.

Received:2018-01-30 Revised:2018-01-30 Online:2019-04-15 Published:2019-04-26
Contact: DU Lin-xiu
About author:-
Supported by:
-

摘要/Abstract

摘要： 对低碳中锰Q690F高强韧中厚板进行了控扎控冷和热处理工艺试验，观察了显微组织，测定了拉伸和冲击性能，并阐述了其强韧化机制.结果表明:中锰钢的显微组织为亚微米尺度的回火马氏体+逆转变奥氏体的复合层状组织.中锰中厚板1/4厚度位置的屈服强度、抗拉强度、延伸率、-60℃冲击功分别为725MPa，840MPa，27.7%，130J.逆转变奥氏体发生相变诱导塑性(TRIP)效应产生的应变硬化是中锰钢主要的强化机制;TRIP效应吸收大量的应变能，推迟颈缩，增加均匀延伸率，是中锰钢主要的增塑机制;TRIP效应有效地提高了裂纹形成功和裂纹扩展功，是中锰钢主要的韧化机制.

关键词: 中锰钢, Q690F, TRIP效应, 强化机制, 增塑机制, 韧化机制

Abstract: The thermomechanical control process(TMCP) and heat treatment test were conducted on low-C medium-Mn Q690F high strength and toughness mid-thick steel plate. The microstructure of the tested steel was analyzed and the tensile and impact properties were measured. The strengthening and toughening mechanisms were discussed. The results showed that the microstructure of the tested steel is a layered structure composed by sub-micrometer tempered martensite and reverse transformation austenite.The yield strength， tensile strength，elongation， and-60℃ impact energy of the tested plate at 1/4 thickness are 725MPa， 840MPa， 27.7%， 130J， respectively. The strain hardening caused by transformation induced plasticity(TRIP)from the reversed austenite is the main strengthening mechanism. The TRIP effect which absorbs a large amount of strain energy， delays the necking and increases the uniform elongation is considered as the main mechanism for plasticizing. Furthermore， the TRIP effect can increase the energy of the crack initiation and propagation effectively， it is also regraded as the main toughening mechanism.

Key words: medium-Mn steel, Q690F, TRIP effect, strengthening mechanism, plasticizing mechanism, toughening mechanism

中图分类号:

TG115.5

齐祥羽，朱晓雷，胡军，杜林秀. 低碳中锰Q690F高强韧中厚板生产技术[J]. 东北大学学报:自然科学版, 2019, 40(4): 483-487.

QI Xiang-yu， ZHU Xiao-lei， HU Jun， DU Lin-xiu. Production Technology of Low-C Medium-Mn Q690F High Strength and Toughness Mid-Thick Steel Plate[J]. Journal of Northeastern University Natural Science, 2019, 40(4): 483-487.

参考文献

[1]Liu D S，Cheng B G，Chen Y Y.Strengthening and toughening of a heavy plate steel for shipbuilding with yield strength of approximately 690MPa ［J］.Metallurgical and Materials Transactions A，2013，44(1):440-455.
[2]Liu H，Du L X，Hu J，et al.Interplay between reversed austenite and plastic deformation in a directly quenched and intercritically annealed 0.04 C-5Mn low-Al steel［J］.Journal of Alloys and Compounds，2017，695(25):2072-2082.
[3]Hu J，Du L X，Sun G S，et al.The determining role of reversed austenite in enhancing toughness of a novel ultra-low carbon medium manganese high strength steel［J］.Scripta Materialia，2015，104(15):87-90.
[4]Hu J，Du L X，Liu H，et al.Structure-mechanical property relationship in a low-C medium-Mn ultrahigh strength heavy plate steel with austenite-martensite submicro-laminate structure［J］.Materials Science and Engineering:A，2015，647(28):144-151.
[5]蔡志辉，丁桦，薛鑫.新型中锰热轧TRIP钢组织演变及力学性能［J］.东北大学学报(自然科学版)，2013，34(1):62-65.(Cai Zhi-hui，Ding Hua，Xue Xin.Microstructure evolution and mechanical properties of a novel medium-Mn hot-rolled TRIP steel［J］.Journal of Northeastern University(Natural Science)，2013，34(1):62-65.)
[6]Lee S，de Cooman B C.Tensile behavior of intercritically annealed ultra-fine grained 8% Mn multi-phase steel ［J］.Steel Research International，2015，86(10):1170-1178.
[7]Cai Z H，Ding H，Misra R D K.Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content ［J］.Acta Materialia，2015，84(1):229-236.
[8]Haidemenopoulos G N，Kermanidis A T，Malliaros C，et al.On the effect of austenite stability on high cycle fatigue of TRIP 700 steel ［J］.Materials Science and Engineering:A，2013，573(20):7-11.
[9]Abareshi M，Emadoddin E.Effect of retained austenite characteristics on fatigue behavior and tensile properties of transformation induced plasticity steel［J］.Materials and Design，2011，32(10):5099-5105.
[10]Zou Y，Xu Y B，Hu Z P，et al.Austenite stability and its effect on the toughness of a high strength ultra-low carbon medium manganese steel plate ［J］.Materials Science and Engineering:A，2016，675(15):153-163.
[11]Gao G H，An B F，Zhang H，et al.Concurrent enhancement of ductility and toughness in an ultrahigh strength lean alloy steel treated by bainite-based quenching-partitioning-tempering process ［J］.Materials Science and Engineering:A，2017，702(15):104-112.
[12]Golchin S，Avishan B，Yazdani S.Effect of 10% ausforming on impact toughness of nanobainite austempered at 300℃ ［J］.Materials Science and Engineering:A，2016，656(22):94-101.

[1]	蔡志辉，张德良，文光奇，周彦君. Fe-11Mn-4Al-0.2C中锰钢动态变形行为及其本构模型[J]. 东北大学学报（自然科学版）, 2021, 42(9): 1275-1281.
[2]	蔡志辉，张德良，周彦君，文光奇. 应变速率对Fe-11Mn-2Al-0.2C中锰钢变形行为的影响[J]. 东北大学学报:自然科学版, 2020, 41(7): 1041-1047.
[3]	王学强，赵金华，袁国，王国栋. 超快冷下X65管线钢微观组织演变及强化机制分析[J]. 东北大学学报:自然科学版, 2019, 40(3): 334-339.
[4]	高彩茹，刘宝喜，潘欢，高秀华. 高韧性420MPa级桥梁钢开发及强化机制分析[J]. 东北大学学报:自然科学版, 2018, 39(8): 1123-1126.
[5]	齐祥羽，董营，胡军，杜林秀. 高强韧低碳中锰钢的弯曲疲劳性能[J]. 东北大学学报:自然科学版, 2018, 39(12): 1712-1716.
[6]	高秀华，张大征，苏冠侨，杜林秀. 海洋平台用中锰钢飞溅区海水腐蚀行为[J]. 东北大学学报:自然科学版, 2017, 38(9): 1234-1238.
[7]	利成宁，袁国，康健，王国栋. 异步热轧对低合金钢显微组织及力学性能的影响[J]. 东北大学学报:自然科学版, 2017, 38(7): 941-945.
[8]	齐祥羽，臧淼，胡军，杜林秀. V-N微合金化Q550D高强度中厚板[J]. 东北大学学报:自然科学版, 2017, 38(4): 502-506.
[9]	崔辰硕，高彩茹，苏冠侨，高秀华. 热轧低碳钒钢强韧化机制的研究[J]. 东北大学学报:自然科学版, 2017, 38(3): 341-345.
[10]	蔡志辉，李志超，才博，丁桦. Fe-8/11Mn-4Al-0.2C钢的力学性能及应变硬化行为[J]. 东北大学学报:自然科学版, 2017, 38(2): 224-228.
[11]	胡军，杜林秀，王万慧，李晶. 590MPa级热轧V-N高强车轮钢组织性能控制[J]. 东北大学学报(自然科学版), 2013, 34(6): 820-823.
[12]	蔡志辉，辛啟斌，孔辉，丁桦. Fe-11Mn-4Al-02C钢的应变硬化行为[J]. 东北大学学报（自然科学版）, 2013, 34(12): 1721-1724.
[13]	蓝慧芳;杜林秀;刘彦春;刘相华;. 控轧控冷工艺对高强度结构钢组织及力学性能的影响[J]. 东北大学学报(自然科学版), 2009, 30(2): 200-204.
[14]	张红梅;许云波;刘振宇;王国栋;. 变形工艺对热轧双相钢显微组织和性能的影响[J]. 东北大学学报(自然科学版), 2007, 28(4): 505-509.
[15]	崔建忠;胡卫民;卢连大;马龙翔. 合金元素对Al-Li合金破断特征的影响[J]. 东北大学学报:自然科学版, 1990, 11(3): 283-287.

低碳中锰Q690F高强韧中厚板生产技术

Production Technology of Low-C Medium-Mn Q690F High Strength and Toughness Mid-Thick Steel Plate

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价