铸造工艺参数对半连续铸造A390合金管坯宏微观组织的影响

doi:10.3969/j.issn.1005-3026.2015.10.013

东北大学学报:自然科学版 ›› 2015, Vol. 36 ›› Issue (10): 1426-1430.DOI: 10.3969/j.issn.1005-3026.2015.10.013

铸造工艺参数对半连续铸造A390合金管坯宏微观组织的影响

左克生，张海涛，秦克，崔建忠

(东北大学材料电磁过程研究教育部重点实验室，辽宁沈阳110819)

收稿日期:2014-09-14 修回日期:2014-09-14 出版日期:2015-10-15 发布日期:2015-09-29
通讯作者: 左克生
作者简介:左克生(1987-)，男，安徽安庆人，东北大学博士研究生; 崔建忠(1950-)，男，黑龙江双城人，东北大学教授，博士生导师.
基金资助:
国家重点基础研究发展计划项目(2012CB723307-03)；国家自然科学基金资助项目(51204046)；中央高校基本科研业务费专项资金资助项目(N130409003).

Effects of Casting Process Parameters on Macrostructure and Microstructure of A390 Alloy Hollow Billet Produced by DC Casting

ZUO Ke-sheng， ZHANG Hai-tao， QIN Ke， CUI Jian-zhong

Key Laboratory of Electromagnetic Processing of Materials， Ministry of Education， Northeastern University， Shenyang 110819， China.

Received:2014-09-14 Revised:2014-09-14 Online:2015-10-15 Published:2015-09-29
Contact: ZHANG Hai-tao
About author:-
Supported by:
-

摘要/Abstract

摘要： 采用半连续铸造方法制备了A390合金管坯.研究了铸造速度和铸造温度对A390合金管坯宏微观组织的影响.结果表明:随着铸造速度由90mm/min提升至120mm/min、铸造温度由800℃增加至850℃，管坯中初生Si宏观分布趋于均匀，初生Si颗粒的平均尺寸逐渐减小.截面尺寸为164mm/60mm的半连续铸造A390合金管坯的最佳铸造工艺参数为:铸造速度110mm/min、铸造温度850℃，可以获得初生Si宏观分布均匀、初生Si颗粒平均尺寸不超过26μm的管坯，管坯内侧的抗拉强度为264MPa，延伸率为0.5%.

关键词: A390合金, 初生Si, 管坯, 铸造温度, 铸造速度

Abstract: DC casting was used to produce A390 alloy hollow billet. The effects of the casting speed and temperature on the macrostructure and microstructure of A390 alloy hollow billets were studied. The results showed that the distribution of primary Si in the hollow billet became more even and the average size of primary Si particle decreased gradually with the increase of the casting speed from 90mm/min to 120mm/min and casting temperature from 800℃ to 850℃，respectively. The optimum casting process parameters for the A390 alloy hollow billets of 164mm/60mm were obtained with the casting speed of 110mm/min and casting temperature of 850℃. The primary Si particles uniformly distributed with their average size less than 26μm obtained under the optimum casting process parameters. The ultimate tensile strength and elongation at the inner wall of the hollow billets were 264MPa and 0.5%， respectively.

Key words: A390 alloy, primary Si, hollow billet, casting temperature, casting speed

中图分类号:

TG146.2

左克生，张海涛，秦克，崔建忠. 铸造工艺参数对半连续铸造A390合金管坯宏微观组织的影响[J]. 东北大学学报:自然科学版, 2015, 36(10): 1426-1430.

ZUO Ke-sheng， ZHANG Hai-tao， QIN Ke， CUI Jian-zhong. Effects of Casting Process Parameters on Macrostructure and Microstructure of A390 Alloy Hollow Billet Produced by DC Casting[J]. Journal of Northeastern University:Natural Science, 2015, 36(10): 1426-1430.

参考文献

[1]Wang F，Ma Y J，Zhang Z Y，et al.A comparison of the sliding wear behavior of a hypereutectic Al-Si alloy prepared by spray-deposition and conventional casting methods［J］.Wear，2004，256(3/4):342-345.
[2]Zuo M，Liu X F，Sun Q Q.Effects of processing parameters on the refinement of primary Si in A390 alloys with a new Al-Si-P master alloy［J］.Journal of Materials Science，2009，44(8):1952-1958.
[3]Cui C，Schulz A，Schimanski K，et al.Spray forming of hypereutectic Al-Si alloy［J］.Journal of Materials Processing Technology，2009，209(11):5220-5228.
[4]Leatham A.Spray forming-alloys，products and markets［J］. Metal Powder Report，1999，51(5):28-37.
[5]魏长传，曹秀萍，石建业.铝及铝合金管材生产［M］.长沙:中南大学出版社，2010:5-6.( Wei Chang-chuan，Cao Xiu-ping，Shi Jian-ye.Tube manufacturing of aluminum and aluminum alloy［M］.Changsha:Central South University Press，2010:5-6.)
[6]Lasa L，Rodriguez-Ibabe J M.Wear behavior of eutectic and hypereutectic Al-Si-Cu-Mg casting alloys tested against a composite brake pad［J］.Materials Science and Engineering A，2003，363，193-202.
[7]Zhang Q，Li T J，Wang T M，et al.Effects of AC magnetic field on solidification structure of continuously cast hollow billet［J］.Ironmaking and Steelmaking，2009，36(2):115-119.
[8]Xu C L，Jiang Q C.Morphologies of primary silicon in hypereutectic Al-Si alloys with melt overheating temperature and cooling rate［J］.Materials Science and Engineering A，2006，437:451-455.(上接第1425页)3结论1) Mg-5Li合金中加入Y后，合金中生成了稀土化合物Mg₂₄Y₅.Mg₂₄Y₅相阻碍了合金在挤压过程中动态再结晶晶粒的长大，显著细化了合金的晶粒.经过挤压变形后，Mg-5Li-xY合金中出现了明显的挤压带，合金中稀土化合物表现出沿挤压方向分布的特征.2) Mg-5Li合金中添加Y后主要产生了固溶强化、细晶强化及第二相强化，使得挤压态合金的力学性能有了较大提升.随Y质量分数的增加，合金的抗拉强度、伸长率等力学性能呈先上升后下降的趋势，Y质量分数过高时易导致合金中稀土相体积过大并发生团聚，降低了第二相强化作用.3) 挤压态Mg-5Li-3Y合金获得了较好的力学性能，其抗拉强度和断裂伸长率分别达到了231.63MPa和9.35%.合金的室温拉伸断裂方式以韧性断裂为主.

铸造工艺参数对半连续铸造A390合金管坯宏微观组织的影响

Effects of Casting Process Parameters on Macrostructure and Microstructure of A390 Alloy Hollow Billet Produced by DC Casting

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

本文评价

[1]	王东涛，张海涛，韩星，崔建忠. 铸造速度和混合稀土对Al-23%Si合金组织和性能的影响[J]. 东北大学学报:自然科学版, 2017, 38(4): 507-512.
[2]	韩星，邵博，张海涛，崔建忠. 复合铸锭包覆铸造的数值模拟[J]. 东北大学学报:自然科学版, 2014, 35(7): 969-974.
[3]	王哲峰;崔建忠;朴凤贤. 铝合金空心管坯电磁铸造中磁场分布的数值模拟[J]. 东北大学学报(自然科学版), 2005, 26(3): 244-247.
[4]	刘丹;崔建忠;夏克农. 液相线铸造铝合金2618显微组织[J]. 东北大学学报(自然科学版), 1999, 20(2): 4--.