杏山铁矿斜分条分段崩落法试验研究

doi:10.12068/j.issn.1005-3026.2021.12.011

东北大学学报（自然科学版） ›› 2021, Vol. 42 ›› Issue (12): 1747-1752.DOI: 10.12068/j.issn.1005-3026.2021.12.011

杏山铁矿斜分条分段崩落法试验研究

乔夏梁¹，任凤玉¹，曹建立¹，师宏伟²

(1. 东北大学资源与土木工程学院，辽宁沈阳110819; 2. 首钢矿业公司杏山铁矿，河北迁安064400)

修回日期:2021-05-06 接受日期:2021-05-06 发布日期:2021-12-17
通讯作者: 乔夏梁
作者简介:乔夏梁(1991-)，男，辽宁沈阳人，东北大学博士研究生；任凤玉(1956-)，男，内蒙古赤峰人，东北大学教授，博士生导师.
基金资助:
“十三五”国家重点研发计划项目 (2016YFC0801600)；国家自然科学基金重点资助项目 (51534003).

Experimental Study of the Inclined Slices Sublevel Caving Method in Xingshan Iron Mine

QIAO Xia-liang¹， REN Feng-yu¹， CAO Jian-li¹， SHI Hong-wei²

1. School of Resources & Civil Engineering， Northeastern University， Shenyang 110819， China; 2. Shougang Mining Corporation Xingshan Iron Mine， Qian’an 064400， China.

Revised:2021-05-06 Accepted:2021-05-06 Published:2021-12-17
Contact: QIAO Xia-liang
About author:-
Supported by:
-

摘要/Abstract

摘要： 杏山铁矿小杏山采区为层状倾斜厚矿体，原用垂直走向布置进路的无底柱分段崩落法开采，存在矿石损失贫化大、上盘侧回采进路地压显现严重、巷道支护工程量大等生产问题.研究提出斜分条分段崩落采矿法，即沿矿体延深方向，从上盘到下盘按斜线分条开采，每一分条在矿体里布置诱导冒落进路，在崩落本分段矿石的同时，诱导近上盘矿体自然冒落，冒落的矿石由设置在下盘围岩里的回收进路回采.该法较好地顺应了倾斜矿体崩落矿石的移动规律，降低了采切工程总成本.试验采场自2019年5月开始回采，现已回采两个分段，矿石回采率由74%提高到85.6%，贫化率由18%降低到15%，取得了良好的技术经济指标.

关键词: 倾斜厚矿体;斜分条分段崩落法;矿石回采指标;诱导冒落;采场结构

Abstract: The orebody in Xiaoxingshan mining area of Xingshan iron mine is layered inclined thick.Originally， the sublevel caving method without sill pillar was used for mining with drift perpendicular to strike， resulting in high ore loss and dilution， serious underground pressure behavior at hanging wall side of drift， large amount of roadway support engineering， and so on.Therefore， the inclined slices sublevel caving method is proposed. Along the deepening direction， orebody is mined according to the inclined line from the hanging wall to the footwall.An induced caving drift was arranged in each orebody slices.Current sublevel ore is caved， meanwhile the orebody near the hanging wall is also induced to cave naturally， and the caved ore is mined by the recovery drift set in the footwall surrounding rock. This method conforms to the movement law of ore caving in the inclined orebody， reduces the total cost of development and cut engineering.The experimental stope has been mined since May 2019， and now two sublevels has been mined， the ore recovery rate increased from 74% to85.6%， and the dilution rate has been reduced from 18% to 15%. New method has achieved good technical and economic indexes.

Key words: inclined thick orebody; inclined slices sublevel caving method; ore mining indexes; induced caving; stope structure

中图分类号:

TD853.36

乔夏梁，任凤玉，曹建立，师宏伟. 杏山铁矿斜分条分段崩落法试验研究[J]. 东北大学学报（自然科学版）, 2021, 42(12): 1747-1752.

QIAO Xia-liang， REN Feng-yu， CAO Jian-li， SHI Hong-wei. Experimental Study of the Inclined Slices Sublevel Caving Method in Xingshan Iron Mine[J]. Journal of Northeastern University(Natural Science), 2021, 42(12): 1747-1752.

参考文献

[1]王青，任凤玉.采矿学［M］.北京:冶金工业出版社，2011.(Wang Qing，Ren Feng-yu.Mining science［M］.Beijing:Metallurgical Industry Press，2011.)
[2]Shekhar G，Gustafson A，Boeg-Jensen P，et al.Draw control strategies in sublevel caving mines:a baseline mapping of LKAB’s Malmberget and Kiirunavaara mines［J］.Journal of the Southern African Institute of Mining and Metallurgy，2018，118(7):723-733.
[3]Morrison G W.Stratigraphic control of Cu-Fe skarn ore distribution and genesis at Craigmont，British Columbia［J］.CIM Bulletin，1980，73(820):109-123.
[4]Cave B，Lilly R，Barovich K.Textural and geochemical analysis of chalcopyrite，galena and sphalerite across the Mount Isa Cu to Pb-Zn transition:implications for a zoned Cu-Pb-Zn system［J］.Ore Geology Reviews，2020，124:103647.
[5]惠安社，李明楼，路增祥，等.我国无底柱分段崩落法结构参数优化研究进展与方向［J］.金属矿山，2020(3):1-11.(Hui An-she，Li Ming-lou，Lu Zeng-xiang，et al.Study progress and direction of structural parameters optimization of non-pillar sublevel caving method in China［J］.Metal Mine，2020(3):1-11.)
[6]余健.高分段大间距无底柱分段崩落采矿贫化损失预测与结构参数优化研究［D］.长沙:中南大学，2007.(Yu Jian.Research on the prediction of ore dilution and loss rate and the optimization of structural parameters of high sublevel large-space drive interval pillarless sublevel caving［D］.Changsha:Central South University，2007.)
[7]Brunton I D，Fraser S J，Hodgkinson J H，et al.Parameters influencing full scale sublevel caving material recovery at the Ridgeway gold mine［J］.International Journal of Rock Mechanics and Mining Sciences，2010，47(4):647-656.
[8]Brunton I.The impact of blasting on sublevel caving material flow behavior and recovery［D］.Brasbane:University of Queensland，2009.
[9]Henning J G，Mitri H S.Assessment and control of ore dilution in long hole mining:case studies［J］.Geotechnical & Geological Engineering，2008，26(4):349-366.
[10]Castro R.Study of the mechanisms of granular flow for block caving［D］.Brasbane:University of Queensland，2006.
[11]Hustrulid W，Kvapil R.Sublevel caving-past and future［C］//Proceedings of the 5th International Conference and Exhibition on Mass Mining.Lulea，2008:107-132.
[12]Zhou C B，Yao Y K，Guo L W，et al.Numerical simulation of independent advance of ore breaking in the non-pillar sublevel caving method［J］.Journal of China University of Mining and Technology， 2007，17(2):295-300.
[13]Guo J，Gan D Q，Tan J，et al.Analysis on monitor and experiment of blasting vibration for Sijiaying Iron Mine ［J］.Applied Mechanics & Materials，2012，214:407-411.
[14]Vyazmensky A，Elmo D，Stead D.Role of rock mass fabric and faulting in the development of block caving induced surface subsidence［J］.Rock Mechanics & Rock Engineering，2010，43(5):533-556.
[15]Chitombo G P.Cave mining:16 years after Laubscher’s 1994 paper ‘Cave mining—state of the art’［J］.Mining Technology，2010，119(3):132-141.
[16]Castro R L，Gonzalez F，Arancibia E.Development of a gravity flow numerical model for the evaluation of drawpoint spacing for block/panel caving［J］.Journal of the Southern African Institute of Mining and Metallurgy， 2009，109(7):393-400.
[17]Zhang X，Tao G，Zhu Z.Laboratory study of the influence of dip and ore width on gravity flow during longitudinal sublevel caving［J］.International Journal of Rock Mechanics and Mining Sciences，2018，103:179-185.
[18]Suglo R S，Opoku S.An assessment of dilution in sublevel caving at Kazansi mine［J］.International Journal of Mining & Mineral Engineering，2012，4(1):1-16.
[19]李鹏程，叶义成，姚囝，等.宜昌晒旗河磷矿条带充填法采场结构及回采顺序研究［J］.金属矿山，2019，48(9):34-40.(Li Peng-cheng，Ye Yi-cheng，Yao Nan，et al.Study on the optimization of mining scheme for gently inclined thin orebody of Shaiqi river phosphorite mine in Yichang city［J］.Metal Mine，2019，48(9):34-40.)
[20]Guo Q F，Ren F H.Optimization and tests on the independent advance of ore breaking with high sublevel and large drift interval［J］.Advanced Materials Research，2011，361/362/363:120-124.
[21]Salinas D V.Calibration of a mixing model for sublevel caving［D］.Vancouver:University of British Columbia，2012.
[22]Trueman R，Castro R，Halim A.Study of multiple draw-zone interaction in block caving mines by means of a large 3D physical model［J］.International Journal of Rock Mechanics and Mining Sciences，2008，45(7):1044-1051.
[23]Tao G，Lu M，Zhang X，et al.A new diversion drawing technique for controlling ore loss and dilution during longitudinal sublevel caving［J］. International Journal of Rock Mechanics and Mining Sciences，2019，113:163-171.
[24]Gang C.Stochastic modeling of rock fragment flow under gravity［J］.International Journal of Rock Mechanics & Mining Sciences，1997，34(2):323-331.
[25]Jin A，Sun H，Ma G，et al.A study on the draw laws of caved ore and rock using the discrete element method［J］.Computers and Geotechnics，2016，80:59-70.
[26]曹建立，任凤玉，张晋军，等.分段卸压崩落法导流放矿实验研究［J］.东北大学学报(自然科学版)，2011，32(8):125-128.(Cao Jian-li，Ren Feng-yu，Zhang Jin-jun，et al.Experimental study on diversion drawing by stress-relief sublevel caving method［J］.Journal of Northeastern University(Natural Science)，2011，32(8):125-128.)
[27]Vivanco F，Melo F.The effect of rock decompaction on the interaction of movement zones in underground mining［J］.International Journal of Rock Mechanics & Mining Sciences，2013，60:381-388.
[28]Melo F，Vivanco F，Fuentes C，et al.On drawbody shapes:from Bergmark-Roos to kinematic models［J］.International Journal of Rock Mechanics & Mining Sciences， 2007，44(1):77-86.
[29]Melo F，Vivanco F，Fuentes C.Calculated isolated extracted and movement zones compared to scaled models for block caving［J］.International Journal of Rock Mechanics & Mining Sciences，2009，46(4):731-737.
[30]贾海波，任凤玉，何荣兴，等.缓倾斜厚石膏矿低贫化放矿实验研究［J］.东北大学学报(自然科学版)，2019，40(11):1617-1622.(Jia Hai-bo，Ren Feng-yu，He Rong-xing，et al.Experimental study of low dilution drawing in gently inclined thick gypsum deposit［J］.Journal of Northeastern University(Natural Science)，2019，40(11):1617-1622.)［31］康红普.我国煤矿巷道围岩控制技术发展70年及展望［J］.岩石力学与工程学报，2021，40(1):1-30.(Kang Hong-pu.Seventy years development and prospects of strata control technologies for coal mine roadways in China［J］.Chinese Journal of Rock Mechanics and Engineering， 2021，40(1):1-30.)［32］任凤玉.随机介质放矿理论及其应用［M］.北京:冶金工业出版社，1994.(Ren Feng-yu.Theory of stochastic medium ore drawing and its application［M］.Beijing:Metallurgical Industry Press，1994.)

杏山铁矿斜分条分段崩落法试验研究

Experimental Study of the Inclined Slices Sublevel Caving Method in Xingshan Iron Mine

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics

本文评价

[1]	由希，张国建. 覆岩散体粒径空间分布对岩石混入的影响[J]. 东北大学学报:自然科学版, 2016, 37(11): 1604-1608.
[2]	马姣阳，任凤玉，曹建立，闫喜明. 急倾斜破碎中厚矿体诱导冒落法进路位置实验研究[J]. 东北大学学报:自然科学版, 2015, 36(8): 1175-1179.