基于CFD模拟的喷射泵操作参数对泵抽气性能的影响

doi:10.12068/j.issn.1005-3026.2019.11.014

东北大学学报:自然科学版 ›› 2019, Vol. 40 ›› Issue (11): 1595-1599.DOI: 10.12068/j.issn.1005-3026.2019.11.014

基于CFD模拟的喷射泵操作参数对泵抽气性能的影响

韩宇，郭立新，王晓冬，张光利

(东北大学机械工程与自动化学院，辽宁沈阳110819)

收稿日期:2019-02-15 修回日期:2019-02-15 出版日期:2019-11-15 发布日期:2019-11-05
通讯作者: 韩宇
作者简介:韩宇(1985-)，女，辽宁抚顺人，东北大学博士研究生; 郭立新(1968-)，男，辽宁沈阳人，东北大学教授，博士生导师；王晓冬(1963-)，男，辽宁沈阳人，东北大学教授.
基金资助:
国家自然科学基金资助项目(51775098).

Influence of Operating Parameters on the Ejector Performance Based on CFD Simulation

HAN Yu， GUO Li-xin， WANG Xiao-dong， ZHANG Guang-li

School of Mechanical Engineering & Automation， Northeastern University， Shenyang 110819， China.

Received:2019-02-15 Revised:2019-02-15 Online:2019-11-15 Published:2019-11-05
Contact: WANG Xiao-dong
About author:-
Supported by:
-

摘要/Abstract

摘要： 通过CFD方法讨论了不同操作参数对喷射泵内部流体的流动特性及泵抽气性能的影响.随着工作蒸汽压力的增加，在壅塞位置处，被抽气体过流面积变化减小，马赫数、引射系数升高，喷射泵的抽气性能增强.当工作蒸汽压力过高时，由于膨胀核的增大，被抽气体的过流面积减小，引射系数显著下降.随着引射蒸汽压力的增加，壅塞和激波向下游移动，泵抽气性能增强.此外，引射系数随着背压的增加而减小，当背压过高时，返流现象明显，泵的抽气性能急剧下降直至失效.研究结果表明，操作参数的选择不仅能提高喷射泵的抽气效率和极限排气能力，也极大地提高了喷射制冷系统的制冷效率，降低了能源的消耗.

关键词: 喷射泵, 壅塞, 激波, 引射系数, 背压

Abstract: The influences of the different operating parameters on flow characteristic of internal flow field and the ejector performance are discussed by CFD method. With the increase of the primary fluid pressure， the flow area of the secondary fluid pressure decreases at the choking position， however， the Mach number and the entrainment ratio both gradually increased， and the pumping performance is enhanced. When the pressure is too high， the flow region of the secondary fluid is compressed due to the increase of the expansion core and the entrainment ratio decreases obviously. With the increasing of the primary fluid pressure， the choking position and the shock wave moves downstream. The pumping performance of the ejector is strengthened. The entrainment ratio decreases with the increase of the back pressure. When the back pressure is too high， the reflux phenomenon is obvious and the pumping performance decreases sharply until it loses efficiency. The results indicated that the reasonable selection of the operating parameters can not only improve the pumping efficiency and exhaust capacity of the ejector， but also greatly improve the refrigeration efficiency of jet refrigeration system and reduce the energy consumption.

Key words: ejector, choke, shock wave, entrainment ratio, back pressure

中图分类号:

TQ021

韩宇，郭立新，王晓冬，张光利. 基于CFD模拟的喷射泵操作参数对泵抽气性能的影响[J]. 东北大学学报:自然科学版, 2019, 40(11): 1595-1599.

HAN Yu， GUO Li-xin， WANG Xiao-dong， ZHANG Guang-li. Influence of Operating Parameters on the Ejector Performance Based on CFD Simulation[J]. Journal of Northeastern University Natural Science, 2019, 40(11): 1595-1599.

参考文献

[1]Arnold H G，Huntley W R，Perez-Blanco H.Steam ejector as an industrial heat pump Semiannual meeting of the American society of heating ［M］.Houston:Refrigerating，and Air Conditioning Engineers，1982.
[2]Chunnanond K，Aphornratana S.An experimental investigation of a steam ejector refrigerator:the analysis of the pressure profile along the ejector ［J］.Applied Thermal Engineering，2004，24:311-322.
[3]Lee G，Lee Y，Ji M.CFD analysis of flow phenomena inside thermo vapor compressor influenced by operating conditions and converging duct angles ［J］.Journal of Mechanical Science and Technology，2009，23:2366-2375.
[4]Haghparast P，Sorin M V，Nesreddine H.The impact of internal ejector working characteristics and geometry on the performance of a refrigeration cycle ［J］.Energy，2018，162:728-743.
[5]Riffat S B，Omer S A.CFD modelling and experimental investigation of an ejector refrigeration system using methanol as the working fluid ［J］.International Journal of Energy Research，2001，25:115-128.
[6]王晓冬，付强，易舒.蒸汽喷射制冷系统喷射泵工作特性的实验研究［J］.东北大学学报(自然科学版)，2017，38(12):1744-1747.(Wang Xiao-dong，Fu Qiang，Yi Su.Experimental study on the working characteristics of the ejector in steam jet refrigeration system ［J］.Journal of Northeastern University(Natural Science)，2017，38(12):1744-1747.)
[7]王晓冬，董敬亮，雷宏建，等.水喷射泵的数值模拟［J］.真空科学与技术，2013，33(11):1069-1073.(Wang Xiao-dong，Dong Jing-liang，Lei Hong-jian，et al.Numerical simulation of water jet pump ［J］.Chinese Journal of Vacuum Science and Technology，2013，33(11):1069-1073.)
[8]Wang X D，Dong J L，Li A，et al.Numerical study of primary steam superheating effects on steam ejector flow and its pumping performance ［J］.Energy，2014，78:205-211.
[9]Sun D W.Variable geometry ejector and their applications in ejector refrigeration systems ［J］.Elsevier Science Ltd and IIR，1996，21(10):919-929.
[10]Li A，Yeoh G H，Yuen A C Y，et al.Numerical simulation of condensation effect on a steam ejector by wet steam model ［C］//Thirteenth International Conference on Flow Dynamics.Sendai，2016:10-12.
[11]Li A，Yuen A C Y，Chen T B Y，et al.Computational study of wet steam flow to optimize steam ejector efficiency for potential fire suppression application ［J］.Applied Sciences，2019，9(7):1486-1487.
[12]Bartosiewicz Y，Aidoun Z，Mercadier Y.Numerical assessment of ejector operation for refrigeration applications based on CFD ［J］.Applied Thermal Engineering，2006，26:604-612.
[13]Desevaux P，Mellal A，Sousa Y A D.Visualization of secondary flow choking phenomena in a supersonic air ejector ［J］.Journal of Visualization，2004，7:249-256.
[14]Bouhanguel A，Desevaux P，Gavignet E.Flow visualization in supersonic ejectors using laser tomography techniques ［J］.International Journal of Refrigeration，2011，34:1633-1640.
[15]Sriveerakul T，Aphormratana S，Chunnanond K.Performance prediction of steam ejector using computational fluid dynamics ［J］.International Journal of Thermal Sciences，2007，46:812-833
[16]Haghparast P，Sorin M V，Nesreddine H.The impact of internal ejector working characteristics and geometry on the performance of a refrigeration cycle ［J］.Energy，2018，162:728-743.
[17]张家豪.小型蒸汽喷射实验系统的结构改进和性能提高［D］.沈阳:东北大学，2015.(Zhang Jia-hao.Structural improvement and performance improvement of small steam ejector experimental system ［D］.Shenyang:Northeastern University，2015.)
[18]Pianthong K，Seehanam W，Behnia M，et al.Investigation and improvement of ejector refrigeration system using computational fluid dynamics technique ［J］.Energy Conversion and Management，2007，48:2556-2564.
[19]Besagni G，Mereu R，Inzoli F.CFD study of ejector flow behavior in a blast furnace gas galvanizing plant ［J］.International Journal of Thermal Sciences，2015，24:58-66.
[20]Besagni G，Mereu R，Chiesa P，et al.An integrated lumped parameter-CFD approach for off-design ejector performance evaluation ［J］.Energy Conversion and Management，2015，105:697-715.
[21]Han Y，Wang X D，Sun H，et al.CFD simulation on the boundary layer separation in the steam ejector and its influence on the pumping performance ［J］.Energy，2015，105:697-715.(上接第1594页)
[6]Khurshid M，Leitner M，Barsoum Z，et al.Residual stress state induced by high frequency mechanical impact treatment in different steel grades-numerical and experimental study ［J］.International Journal of Mechanical Sciences，2017，123:34-42.
[7]Hu S，Guo C，Wang D，et al.3D dynamic finite element analysis of the nonuniform residual stress in ultrasonic impact treatment process ［J］.Journal of Materials Engineering & Performance，2016，25(9):4004-4015.
[8]Liu Y，Wang D，Deng C，et al.Influence of re-ultrasonic impact treatment on fatigue behaviors of S690QL welded joints ［J］.International Journal of Fatigue，2014，66(6):155-160.
[9]刘福超，雷丽萍，曾攀.滚压有限元模型数值模拟［J］.塑性工程学报，2012，19(2):17-21.(Liu Fu-chao，Lei Li-ping，Zeng Pan.Surface rolling FE model for numerical simulation ［J］.Journal of Plasticity Engineering，2012，19(2):17-21.)
[10]Toyserkani E，Khajepour A，Corbin S.3-D finite element modeling of laser cladding by powder injection:effects of laser pulse shaping on the process ［J］.Optics & Lasers in Engineering，2004，41(6):849-867.
[11]Zhao H，Zhang G，Yin Z，et al.Three-dimensional finite element analysis of thermal stress in single-pass multi-layer weld-based rapid prototyping ［J］.Journal of Materials Processing Technology，2012，212(1):276-285.
[12]胡宝.TC4钛合金薄壁件激光焊接数值模拟研究［D］.天津:天津大学，2014.(Hu Bao.Research on numerical simulation of laser welding for thin-walled TC4 titanium alloy ［D］.Tianjin: Tianjin University，2014.)
[13]樊湘芳，邱长军，周炬，等.高频微锻造对激光熔覆层开裂行为与表面组织的影响［J］.焊接学报，2011，32(1):101-104.(Fan Xiang-fang，Qiu Chang-jun，Zhou Ju，et al.Effects of high frequency micro-forging on the cracking behavior and surface structure of laser cladding ［J］.Transactions of the China Welding Institution，2011，32(1):101-104.)

基于CFD模拟的喷射泵操作参数对泵抽气性能的影响

Influence of Operating Parameters on the Ejector Performance Based on CFD Simulation

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 6

编辑推荐

Metrics

本文评价

[1]	王晓冬，孙浩林，孙浩. 喷嘴调节锥对水蒸气喷射泵性能影响的数值模拟[J]. 东北大学学报:自然科学版, 2020, 41(5): 706-710.
[2]	王晓冬，孙浩，宁久鑫，孙浩林. 基于CFD评估蒸汽喷射泵的抗背压能力[J]. 东北大学学报:自然科学版, 2020, 41(3): 399-402.
[3]	王晓冬，付强，易舒，李赫. 蒸汽喷射制冷系统喷射器工作特性的实验研究[J]. 东北大学学报:自然科学版, 2017, 38(12): 1744-1747.
[4]	李强;冯明霞;邹宗树;沈峰满;. 壅塞现象法测量气粉两相流音速[J]. 东北大学学报(自然科学版), 2007, 28(10): 1417-1420.
[5]	王晓鸣;李强;邹宗树;沈峰满;. 利用壅塞原理均匀分配高炉各风口的喷煤量[J]. 东北大学学报(自然科学版), 2006, 27(9): 999-1002.
[6]	韩珽;彭一川. 等截面摩擦管中气粉流的壅塞现象[J]. 东北大学学报:自然科学版, 1995, 16(4): 5--.