东北大学学报（自然科学版）

东北大学学报（自然科学版） ›› 2021, Vol. 42 ›› Issue (3): 428-435.DOI: 10.12068/j.issn.1005-3026.2021.03.019

• 资源与土木工程 • 上一篇    下一篇

全螺栓连接和焊接连接钢板剪力墙力学性能分析

牟在根1， 大海1， 杨雨青1， 王喆2   

  1. (1. 北京科技大学 土木与资源工程学院， 北京100083; 2. 中国建筑标准设计研究院， 北京100048)
  • 收稿日期:2020-02-26 修回日期:2020-02-26 接受日期:2020-02-26 发布日期:2021-03-12
  • 通讯作者: 牟在根
  • 作者简介:牟在根(1960-)，男，黑龙江佳木斯人，北京科技大学教授，博士生导师.
  • 基金资助:
    国家自然科学基金资助项目(51578064)； 北京市自然科学基金资助项目(8172031).

Analysis on Mechanical Properties of the Steel Plate Shear Wall with Fully Bolted and Welded Connections

MU Zai-gen1， DA Hai1， YANG Yu-qing1， WANG Zhe2   

  1. 1. School of Civil and Resource Engineering， University of Science and Technology Beijing， Beijing 100083， China; 2. China Institute of Building Standard Design & Research， Beijing 100048， China.
  • Received:2020-02-26 Revised:2020-02-26 Accepted:2020-02-26 Published:2021-03-12
  • Contact: YANG Yu-qing
  • About author:-
  • Supported by:
    -

RichHTML

12

PDF (PC)

296

摘要： 为了避免焊接造成的残余应力，通过螺栓连接的端板将上下2块钢板连接，形成一种延性和耗能能力更好的全螺栓连接钢板墙.通过有限元建立全螺栓连接和传统焊接连接钢板墙模型，对比两种钢板墙在单向推覆和往复荷载作用下的荷载位移曲线、抗侧承载性能、能量耗散系数、刚度退化和承载力退化等性能.结果表明，在单向推覆作用下全螺栓连接钢板墙的抗侧承载力与传统焊接形式较为接近，但初始刚度比传统形式下降了11%;在往复荷载作用下，全螺栓连接形式表现出更好的整体耗能能力，刚度退化更平缓.该类钢板墙还便于生产和安装，在今后的工程应用中值得广泛的推广和应用.

关键词: 钢板剪力墙;螺栓连接;两边连接;抗剪性能;滞回性能

Abstract: In order to avoid the residual stress caused by welding， the upper and lower steel plates are connected by the end-plate with bolts to form a fully bolted steel plate shear wall (SPSW) with better ductility and energy dissipation capacity. The models of fully bolted SPSW and welded SPSW were established and analyzed by the finite element method. The load-displacement curve， lateral bearing capacity， energy dissipation capacity， stiffness degradation， and bearing capacity degradation of the two kinds of steel plate shear walls under unidirectional push-over and reciprocating load were compared. The results show that， under the action of unidirectional push-over， the lateral bearing capacity of the SPSW with full bolted is close to that of the traditional form， but the initial stiffness is 11% lower than that of the traditional form. Under the reciprocating load， the SPSW with full bolted shows a better overall energy dissipation capacity， and the stiffness degrades slower. This form of SPSW is also convenient for production and installation， and worth to extensive promotion and application in the future engineering application.

Key words: steel plate shear wall(SPSW); bolted connections; beam-only connection; shear property; hysteretic property

中图分类号: