Zr对Al-10Zn-2.5Mg-1.6Cu合金板材组织与性能的影响

doi:10.12068/j.issn.1005-3026.2022.07.006

东北大学学报（自然科学版） ›› 2022, Vol. 43 ›› Issue (7): 951-958.DOI: 10.12068/j.issn.1005-3026.2022.07.006

Zr对Al-10Zn-2.5Mg-1.6Cu合金板材组织与性能的影响

田妮^{1, 2}，张耀中¹，周轶然¹，秦广华³

(1.东北大学材料科学与工程学院，辽宁沈阳110819； 2.东北大学材料各向异性与织构教育部重点实验室，辽宁沈阳110819；3.沈阳铸造研究所有限公司，辽宁沈阳110022)

发布日期:2022-08-02
通讯作者: 田妮
作者简介:田妮(1975-)，女，湖南永顺人，东北大学副教授.
基金资助:
国家自然科学基金资助项目(51871043)；中央高校基本科研业务费专项资金资助项目(N180212010)；辽宁省自然科学基金资助项目(2019-MS-113).

Effect of Zr Addition on Microstructure and Mechanical Properties of Al-10Zn-2.5Mg-1.6Cu Alloy Sheet

TIAN Ni^{1, 2}， ZHANG Yao-zhong¹， ZHOU Yi-ran¹， QIN Guang-hua³

1. School of Materials Science & Engineering， Northeastern University， Shenyang 110819， China; 2. Key Laboratory for Anisotropy and Texture of Materials， Ministry of Education， Northeastern University， Shenyang 110819， China; 3. Shenyang Research Institute of Foundry Co.， Ltd.， Shenyang 110022， China.

Published:2022-08-02
Contact: TIAN Ni
About author:-
Supported by:
-

摘要/Abstract

摘要： 针对T6态Al-10Zn-2.5Mg-1.6Cu铝合金板材，研究了添加质量分数分别为0，0.046%，0.098%，0.151%，0.185%的Zr，铝板中合金相粒子和晶粒的组态以及板材的力学性能.结果表明，Zr含量增加对铝板中微米级T相和Al₇Cu₂Fe相粒子无明显影响，合金中未形成含Zr的结晶相，但纳米级Al₃Zr弥散相粒子数量逐渐增多.添加质量分数为0.046% Zr可细化T6态铝板等轴状Cube取向晶粒；Zr质量分数超过0.098%能抑制铝板再结晶形核，板材晶粒为纤维状，取向以Brass，S，R和Copper为主，且其体积分数随Zr含量增加而逐渐增大.Zr含量增加，T6态铝板的强度逐渐增大，而延伸率先增大后略有减小.Zr质量分数为0.151%的T6态Al-10Zn-2.5Mg-1.6Cu铝合金板材性能最佳，其抗拉强度、屈服强度和延伸率分别为706，645MPa和10.3%.

关键词: Al-10Zn-2.5Mg-1.6Cu合金板材；Zr含量；合金相；再结晶；织构；力学性能

Abstract: The mechanical properties and microstructure， such as the phase configuration and the grain characteristics of the T6 temper Al-10Zn-2.5Mg-1.6Cu alloy sheet were investigated with the Zr addition of 0， 0.046%， 0.098%， 0.151% and 0.185%， respectively. The results show that there is no obvious change of the micro-sized T and Al₇Cu₂Fe phases in the samples， the Zr-containing constituent phases cannot be formed and the number of Al₃Zr dispersoid nanoparticles increases with the Zr addition. Adding 0.046% Zr can refine the equiaxed Cube-oriented grains of the sample. When the Zr content exceeds 0.098%， the recrystallization nucleation can be inhibited， most of the grain shape are fibrous and the grain texture is mainly Brass， S， R and Copper orientations and its fraction increases with the Zr content. When the Zr content increases， the yield and tensile strength of the samples increase gradually and the final elongation firstly increases and then slightly decreases. The T6 temper Al-10Zn-2.5Mg-1.6Cu alloy sheet with the 0.151% Zr has the optimal performance， associated with the tensile and yield strength and final elongation of 706， 645MPa and 10.3%， respectively.

Key words: Al-10Zn-2.5Mg-1.6Cu alloy sheet; Zr content; alloy phase; recrystallization; texture; mechanical property

中图分类号:

TP146.21

田妮，张耀中，周轶然，秦广华. Zr对Al-10Zn-2.5Mg-1.6Cu合金板材组织与性能的影响[J]. 东北大学学报（自然科学版）, 2022, 43(7): 951-958.

TIAN Ni ， ZHANG Yao-zhong， ZHOU Yi-ran， QIN Guang-hua. Effect of Zr Addition on Microstructure and Mechanical Properties of Al-10Zn-2.5Mg-1.6Cu Alloy Sheet[J]. Journal of Northeastern University(Natural Science), 2022, 43(7): 951-958.

参考文献

[1]Georgantzia E，Gkantou M，Kamaris G S.Aluminium alloys as structural material:a review of research ［J］.Engineering Structures，2021，227:111372.
[2]张新明，刘胜胆.航空铝合金及其材料加工［J］.中国材料进展，2013，32(1):39-55.(Zhang Xin-ming，Liu Sheng-dan.Aerocraft aluminum alloys and their materials processing ［J］.Materials China，2013，32(1):39-55.)
[3]Fang H C，Chao H，Chen K H.Effect of Zr，Er and Cr additions on microstructures and properties of Al-Zn-Mg-Cu alloys ［J］.Materials Science and Engineering:A，2014，610:10-16.
[4]Yang Y，Tan P，Sui Y D，et al.Influence of Zr content on microstructure and mechanical properties of as-cast Al-Zn-Mg-Cu alloy ［J］.Journal of Alloys and Compounds，2021，867:158920.
[5]Chiu Y C，Du K T，Bor H Y，et al.The effects of Cu，Zn and Zr on the solution temperature and quenching sensitivity of Al-Zn-Mg-Cu alloys ［J］.Materials Chemistry and Physics，2020，247:122853.
[6]Fang H C，Yang H L，Zhu J M，et al.Effect of minor Cr，Mn，Zr or Ti on recrystallization，secondary phases and fracture behaviour of Al-Zn-Mg-Cu-Yb alloys ［J］.Rare Metal Materials and Engineering，2020，49(3):797-810.
[7]Zhang W，Xing Y，Jia Z H，et al.Effect of minor Sc and Zr addition on microstructure and properties of ultra-high strength aluminum alloy ［J］.Transaction of Nonferrous Metals Society of China，2014，24(12):3866-3871.
[8]Xiao Q F，Huang J W，Jiang Y G，et al.Effects of minor Sc and Zr additions on mechanical properties and microstructure evolution of Al-Zn-Mg-Cu alloys ［J］.Transactions of Nonferrous Metals Society of China，2020，30(6):1429-1438.
[9]谢优华，杨守杰，戴圣龙，等.含锆铝合金的力学性能和强化机理［J］.中国有色金属学报，2003，13(5):1192-1195.(Xie You-hua，Yang Shou-jie，Dai Sheng-long，et al.Mechanical properties and strengthening mechanism of aluminum alloys containing zirconium ［J］.The Chinese Journal of Nonferrous Metals，2003，13(5):1192-1195.)
[10]Ebrahimi S，Emamy R，Pourkia R，et al.The microstructure，hardness and tensile properties of a new super high strength aluminum alloy with Zr addition ［J］.Materials and Design，2010，31(9):4450-4456.
[11]Li Y X，Li P，Zhao G，et al.The constituents in Al-10Zn-2.5Mg-2.5Cu aluminum alloy ［J］.Materials Science and Engineering:A，2005，397:204-208.
[12]Peng Y H，Liu C Y，Wei L L，et al.Quench sensitivity and microstructures of high-Zn-content Al-Zn-Mg-Cu alloys with different Cu contents and Sc addition ［J］.Transactions of Nonferrous Metals Society of China，2021，31(1):24-35.
[13]Li H Y，Jia L N，Huang J H，et al.Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments ［J］.Chinese Journal of Aeronautics，2021，34(2):612-619.
[14]Tang J G，Chen H，Zhang X M，et al.Influence of quench-induced precipitation on aging behavior of Al-Zn-Mg-Cu alloy ［J］.Transactions of Nonferrous Metals Society of China，2012，22(6):1255-1263.
[15]Li W B，Pan Q L，Xiao Y P，et al.Microstructure and mechanical properties of Al-Zn-Cu-Mg-Sc-Zr alloy after retrogression and re-aging treatments ［J］.Journal of Central South University of Technology，2011，18(2):279-284.
[16]Senkov O N，Shagiev M R，Senkova S V，et al.Precipitation of Al₃(Sc，Zr) particles in an Al-Zn-Mg-Cu-Sc-Zr alloy during conventional solution heat treatment and its effect on tensile properties ［J］.Acta Materialia，2008，56(15):3723-3738.
[17]Liu D S，Zhang X M，Chen M A，et al.Effect of Zr content on quench sensitivity of AlZnMgCu alloys ［J］.Transactions of Nonferrous Metals Society of China，2007，17(4):787-792.
[18]Senkov O N，Bhat R B，Senkova S V，et al.Microstructure and properties of cast ingots of Al-Zn-Mg-Cu alloys modified with Sc and Zr ［J］.Metallurgical and Materials Transactions A，2005，36(8):2115-2126.
[19]Engler O，Hirsch J.Texture control by thermomechanical processing of AA6xxx Al-Mg-Si sheet alloys for automotive applications-a review ［J］.Materials Science and Engineering:A，2002，336(1/2):249-262.
[20]薛杰，王有为，张志豪，等.挤压温度对Al-Zn-Mg-Cu合金动态再结晶、时效组织和力学性能的影响［J］.中国有色金属学报，2017，27(11):2204-2211.(Xue Jie，Wang You-wei，Zhang Zhi-hao，et al.Effect of extrusion temperature on dynamic recrystallization，aging microstructure and mechanical properties of Al-Zn-Mg-Cu alloy ［J］.The Chinese Journal of Nonferrous Metals，2017，27(11):2204-2211.)

Zr对Al-10Zn-2.5Mg-1.6Cu合金板材组织与性能的影响

Effect of Zr Addition on Microstructure and Mechanical Properties of Al-10Zn-2.5Mg-1.6Cu Alloy Sheet

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价