东北大学学报（自然科学版）

东北大学学报:自然科学版 ›› 2015, Vol. 36 ›› Issue (7): 942-946.DOI: 10.12068/j.issn.1005-3026.2015.07.007

• 材料与冶金 • 上一篇    下一篇

薄铝带轧制工作辊边部接触的建模与仿真

管健龙， 何安瑞， 孙文权   

  1. (北京科技大学 国家高效轧制中心， 北京100083)
  • 收稿日期:2014-06-09 修回日期:2014-06-09 出版日期:2015-07-15 发布日期:2015-07-15
  • 通讯作者: 管健龙
  • 作者简介:管健龙(1986-)，男，北京顺义人，北京科技大学博士研究生； 何安瑞(1972-)，男，江西抚州人，北京科技大学教授，博士生导师.
  • 基金资助:
    中央高校基本科研业务费专项资金资助项目(FRF-IC-14-005).

Modeling and Simulation of Thin Aluminum Cold Rolling with Work Roll Edge Contact

GUAN Jian-long， HE An-rui， SUN Wen-quan   

  1. National Engineering Research Center for Advanced Rolling Technology， University of Science and Technology Beijing， Beijing 100083， China.
  • Received:2014-06-09 Revised:2014-06-09 Online:2015-07-15 Published:2015-07-15
  • Contact: HE An-rui
  • About author:-
  • Supported by:
    -

RichHTML

0

PDF (PC)

1065

摘要： 为研究冷轧机在轧制薄铝带时工作辊边部接触对辊系受力和铝带断面形状的影响，借鉴弹性悬臂梁法和影响函数法的处理思想，建立了适用于实际生产在线控制的铝冷轧机辊系变形模型，并对不同入口铝带厚度、弯辊力、工作辊的接触状态进行仿真研究.仿真结果表明:工作辊边部接触力随入口厚度增加而增加、随弯辊力增加而减小；工作辊边部接触轧制时，轧机出口铝带凸度和横向厚差小于非边部接触轧制，有利于铝带边部减薄控制，但降低了铝轧机边部板型调控能力，在轧制中应尽量避免.

关键词: 薄铝带冷轧, 悬臂梁, 影响函数, 工作辊边部接触, 辊系变形, 边部减薄

Abstract: A deformation model of roll system in aluminum cold rolling mill applied to online control in the actual production， was established by elastic cantilever beam method and the influence function method processing ideas. The influences of working roll edge contact on the forces acting on the roll system and the cross-sectional shape of aluminum strip in the process of thin aluminum strip rolled by cold rolling mill were studied. The simulation study of different inlet strip thickness， bending force and the contact state of working roll were carried out. The results showed that the contact force of working roll edge increases with the increasing thickness of the entrance， and decreases with the increase of the bending force. When the working roll edge contacts with rolling mill， the difference between outlet strip crown and lateral thickness is less than the non-contact rolling， and this process is useful to reduce edge drop. However， as it reduces the regulatory capacity of the aluminum rolling mill for the edge plate， it should be avoided.

Key words: thin aluminum strip cold rolling, cantilever beam, influence function, working roll edge contact, roll system deformation, edge thinning

中图分类号: