盾构切刀硬质合金与钢基体钎焊残余应力

doi:10.12068/j.issn.1005-3026.2020.01.018

东北大学学报:自然科学版 ›› 2020, Vol. 41 ›› Issue (1): 101-107.DOI: 10.12068/j.issn.1005-3026.2020.01.018

盾构切刀硬质合金与钢基体钎焊残余应力

夏毅敏¹，仝磊¹，柏彬²，华伟明²

(1.中南大学机电工程学院，湖南长沙410083; 2.国网江苏省电力有限公司建设部，江苏南京211000)

收稿日期:2019-05-08 修回日期:2019-05-08 出版日期:2020-01-15 发布日期:2020-02-01
通讯作者: 夏毅敏
作者简介:夏毅敏(1967-)，男，江西永新人，中南大学教授.
基金资助:
国家高技术研究发展计划项目(2012AA041803); 湖南省战略性新兴产业科技攻关项目(2015GK1029)；国家电网公司科技项目(JSJS1600326).

Residual Stress in Soldering and Brazing Between Cemented Carbide and Steel Substrate of Shield Machine Cutters

XIA Yi-min¹， TONG Lei¹， BAI Bin²， HUA Wei-ming²

1. College of Mechanical & Electrical Engineering， Central South University， Changsha 410083， China; 2. Ministry of Construction， State Grid Jiangsu Electric Power Company， Nanjing 211000， China.

Received:2019-05-08 Revised:2019-05-08 Online:2020-01-15 Published:2020-02-01
Contact: XIA Yi-min
About author:-
Supported by:
-

摘要/Abstract

摘要： 针对盾构切刀容易出现焊接裂纹以及残余应力过大导致刀具切削时合金容易剥落的难题，建立了切刀钎焊热力耦合过程有限元分析模型，通过模拟计算和X射线衍射仪对残余应力进行试验验证，研究不同焊接结构切刀的钎焊温度场和残余应力场.研究结果表明，切刀刀头钎焊后冷却过程中温度场呈现梯度分布.当钎料厚度为0.25mm时，刀头应力危险区残余应力最小，160mm刃宽切刀的合金块数设计为3块可降低焊接残余应力、提高焊接强度.残余应力试验结果与数值模拟结果趋势基本吻合，钢基体表面为压应力.

关键词: 盾构切刀, 硬质合金, 钢基体, 钎焊, 残余应力

Abstract: Aiming at the problem that shield machine cutters are prone to welding cracks and the residual stress is too large， which leads to the alloy spalling easily in the cutting process of cutters， the finite element analysis model of the brazing process of cutters was established， and the brazing temperature field and residual stress field of cutters with different welding structures were studied through simulation calculation and X-ray diffractometer experimental verification. The results show that the temperature field presents a gradient distribution in the cooling process after brazing the cutter head. When the thickness of the solder is 0.25mm， the residual stress in the dangerous area of cutter head stress is the smallest. The number of cemented carbide blocks of 160mm blade width cutters is designed as 3 pieces to reduce welding residual stress and improve welding strength. The results of residual stress test are basically consistent with the numerical simulation results， and the surface of steel matrix is compressive stress.

Key words: shield machine cutters, cemented carbide, steel matrix;soldering and brazing, residual stress

中图分类号:

TG454

夏毅敏，仝磊，柏彬，华伟明. 盾构切刀硬质合金与钢基体钎焊残余应力[J]. 东北大学学报:自然科学版, 2020, 41(1): 101-107.

XIA Yi-min， TONG Lei， BAI Bin， HUA Wei-ming. Residual Stress in Soldering and Brazing Between Cemented Carbide and Steel Substrate of Shield Machine Cutters[J]. Journal of Northeastern University Natural Science, 2020, 41(1): 101-107.

参考文献

[1]Li X，Li X，Yuan D.Application of an wear analysis method to cutting tools used in tunneling shields in soft ground［J］.Wear，2017，392:21-28.
[2]Hasanabadi M，Shamsipur A，Sani H N，et al.Interfacial microstructure and mechanical properties of tungsten carbide brazed joints using Ag-Cu-Zn +Ni/Mn filler alloy［J］.Transactions of Nonferrous Metals Society of China，2017，27(12):2638-2646.
[3]Tkalich D，Kane A，Saai A，et al.Wear of cemented tungsten carbide percussive drill-bit inserts:laboratory and field study［J］.Wear，2017，386/387:106-117.
[4]Nagentrau M，Tobi A L M，Kamdi Z，et al.A study on wear failure analysis of tungsten carbide hardfacing on carbon steel blade in a digester tank［J］.Journal of Failure Analysis & Prevention，2017，17(5):861-870.
[5]葛志德，郭勐，荆皓.硬质合金钎焊工艺的研究［J］.机械制造，2018，246(56):60-63.(Ge Zhi-de，Guo Meng，Jing Hao，et al.Study on brazing process of cemented carbide［J］.Machinery，2018，246(56):60-63.)
[6]岳喜山，孙凤莲.硬质合金圆环与钢基体钎焊过程的数值模拟［J］.焊接学报，2005，26(9):35-38.(Yue Xi-shan，Sun Feng-lian.Numerical simulation of brazing process between cemented carbide ring and steel substrate.［J］.Transactions of the China Welding Institution，2005，26(9):35-38.)
[7]刘海汉，李强，陈小勇，等.有限元法在钎焊中残余应力的分析及应用［J］.电焊机，2018，48(1):5-8.(Liu Hai-han，Li Qiang，Chen Xiao-yong，et al.Analysis and application of residual stress in brazing by finite element method［J］.Electric Welding Machine，2018，48(1):5-8.)
[8]黄须强，王大伟，修世超.AISI304/低碳钢真空扩散焊接头组织和性能［J］.东北大学学报(自然科学版)，2017，38(12):1759-1763.(Huang Xu-qiang，Wang Da-wei，Xiu Shi-chao.Microstructure and performance of AISI304 /mild steel vacuum diffusion bonded joint［J］.Journal of Northeastern University(Natural Science)，2017，38(12):1759-1763.)
[9]任朝晖，鞠建忠，吕冬杰，等.试件形状对铝合金摩擦叠焊成形的影响［J］.东北大学学报(自然科学版)，2017，39(7):1000-1004.(Ren Zhao-hui，Ju Jian-zhong，Lyu Dong-jie，et al.Effects of specimen shapes on the friction hydro-pillar processing forming of aluminum alloys［J］.Journal of Northeastern University(Natural Science)，2017，39(7):1000-1004.)
[10]Cui J，Zhai Q，Xu J，et al.Adding Sn on the performance of amorphous brazing fillers applied to brazing TA2 and Q235［J］.Journal of Surface Engineered Materials & Advanced Technology，2014，4(6):342-347.
[11]耿鲁阳，涂善东，巩建鸣，等.不同材料硬化模型模拟13MnNiMoR钢超厚圆筒对接环焊接残余应力［J］.机械工程材料，2019，43(3):60-66.(Geng Lu-yang，Tu Shan-dong，Gong Jian-ming，et al.Simulation of welding residual stress of 13MnNiMoR super thick cylinder butt ring by different material hardening model［J］.Materials for Mechanical Engineering，2019，43(3):60-66.)
[12]Barrena M I，Salazar J M G D，Gómez-Vacas M.Numerical simulation and experimental analysis of vacuum brazing for steel/cermet［J］.Ceramics International，2014，40(7):10557-10563.
[13]Zhang J，Jin L Y .Numerical simulation of residual stress in brazing joint between cemented carbide and steel［J］.Metal Science Journal，2013，21(12):1455-1459.
[14]Sui Y，Luo H，Lv Y，et al.Influence of brazing technology on the microstructure and properties of YG20C cemented carbide and 16Mn steel joints［J］.Welding in the World，2016，60(6):1269-1275.
[15]Nagatsuka K，Sechi Y，Ma N，et al.Simulation of cracking phenomena during laser brazing of ceramics and cemented carbide［J］.Science and Technology of Welding and Joining，2014，19(8):682-688.
[16]Kaiwa K，Yaoita S，Sasaki T，et al.Effects of Ni and Co additions to filler metals on Ag-brazed joints of cemented carbide and martensitic stainless steel［J］.Advanced Materials Research，2014，922:322-327.
[17]Li X，Ye J，Zhang H，et al.Sandblasting induced stress release and enhanced adhesion strength of diamond films deposited on austenite stainless steel［J］.Applied Surface Science，2017，412:366-373.
[15]关守平，房少纯.一种新型的区间-粒子群优化算法［J］.东北大学学报(自然科学版)，2012，33(10):1381-1384.(Guan Shou-ping，Fang Shao-chun.A new particle swarm optimization algorithm［J］.Journal of Northeastern University(Natural Science)，2012，33(10):1381-1384.)(上接第88页)
[7]Sun Y，Gong Y D.Experimental study on the microelectrodes fabrication using low speed wire electrical discharge turning(LS-WEDT) combined with multiple cutting strategy［J］.Journal of Materials Processing Technology，2017，250:121-131.
[8]Fang F Z，Wu H，Liu X D，et a1.Tool geometry study in micro machining［J］.Journal of Micromechanics and Micro Engineering，2003，13(5):726-731.
[9]Kuppan P，Rajadurai A，Narayanan S.Influence of EDM process parameters in deep hole drilling of Inconel 718［J］.The International Journal of Advanced Manufacturing Technology，2008，38(1/2):74-84.
[10]张雷.深小孔微细电火花加工间隙流场仿真及实验研究［D］.哈尔滨:哈尔滨工业大学，2011.(Zhang Lei.Simulation and experiment research of gap flow for micro-EDM deep-small hole machining［D］.Harbin:Harbin Institute of Technology，2011.)
[11]Zhao W S，Wang Z L，Di S C，et al.Ultrasonic and electric discharge machining to deep and small hole on titanium alloy［J］.Journal of Materials Processing Technology，2002，120(1):101-106.
[12]Sun Y，Gong Y D.Experimental study on fabricating spirals microelectrode and micro-cutting tools by low speed wire electrical discharge turning［J］.Journal of Materials Processing Technology，2018，258:271-285.
[13]高连，刘志东，邱明波，等.电火花线切割单晶硅的损伤层［J］.硅酸盐学报，2011，39(5):874-879.(Gao Lian，Liu Zhi-dong，Qiu Ming-bo，et al.Damaged layer of monocrystalline silicon cut by wire electrical discharge machining［J］.Journal of the Chinese Ceramic Society，2011，39(5):874-879.)
[15]关守平，房少纯.一种新型的区间-粒子群优化算法［J］.东北大学学报(自然科学版)，2012，33(10):1381-1384.(Guan Shou-ping，Fang Shao-chun.A new particle swarm optimization algorithm［J］.Journal of Northeastern University(Natural Science)，2012，33(10):1381-1384.)

盾构切刀硬质合金与钢基体钎焊残余应力

Residual Stress in Soldering and Brazing Between Cemented Carbide and Steel Substrate of Shield Machine Cutters

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	任朝晖，王云贺，李竺鸿，王琛. 增材-微锻造加工工艺应力场数值模拟研究[J]. 东北大学学报（自然科学版）, 2022, 43(6): 881-887.
[2]	张东祥，郭立新. 汽车驱动桥壳焊接变形及焊接残余应力有限元仿真分析[J]. 东北大学学报（自然科学版）, 2021, 42(5): 700-705.
[3]	鲍君峰，于月光，贾成厂. ZrO₂添加量对等离子放电烧结制备WC-6Co组织和性能的影响[J]. 东北大学学报（自然科学版）, 2021, 42(1): 43-48.
[4]	李彦龙，吴琼，秦晓峰，刘常升. Cr5支承辊接触疲劳损伤及其次表层组织变化[J]. 东北大学学报:自然科学版, 2020, 41(6): 818-823.
[5]	牛艺静，孙聪，庞刚，修世超. 预应力时效性对磨削强化表面应力的影响[J]. 东北大学学报:自然科学版, 2020, 41(4): 546-550.
[6]	任朝晖，刘振，周世华，段景曦. 钛合金激光熔丝增材制造的温度场与应力场模拟[J]. 东北大学学报:自然科学版, 2020, 41(4): 551-556.
[7]	杨玉莹，巩亚东，屈硕硕，蔡明. 增/减材复合加工316L宏观形貌和残余应力试验[J]. 东北大学学报:自然科学版, 2020, 41(3): 380-386.
[8]	兰亮云，邵国庆，张一婷，王艺南. 焊接顺序对Q690钢T型接头残余应力和变形的影响[J]. 东北大学学报:自然科学版, 2020, 41(12): 1741-1746.
[9]	尹国强，巩亚东，李雨晴，宋俊利. 新型点磨削砂轮磨削表面/亚表面质量研究[J]. 东北大学学报:自然科学版, 2019, 40(6): 835-840.
[10]	任朝晖，刘振，张小双，张兴文. 超声微锻造辅助激光熔丝增材制造数值模拟研究[J]. 东北大学学报:自然科学版, 2019, 40(11): 1590-1595.
[11]	许智峰，周向葵，王凯，王强. SPS预烧结制备超细晶梯度硬质合金[J]. 东北大学学报:自然科学版, 2018, 39(11): 1593-1597.
[12]	石莉，巩亚东，姜增辉. S30T正交车铣TC4钛合金磨损形貌及机理分析[J]. 东北大学学报:自然科学版, 2017, 38(8): 1133-1136.
[13]	卢晓红，王福瑞，路彦君，高路丝. Inconel 718微铣削加工表面残余应力有限元仿真[J]. 东北大学学报:自然科学版, 2017, 38(2): 254-259.
[14]	战宇，刘常升，张凤鹏，邱兆国. 激光超声表面波检测薄板残余应力的数值模拟[J]. 东北大学学报:自然科学版, 2015, 36(3): 406-409.
[15]	张修铭，修世超，王雨时. 磨削液参数对磨削强化表面微结构损伤的影响[J]. 东北大学学报:自然科学版, 2015, 36(10): 1491-1495.