合金设计对贝氏体相变动力学影响的建模研究

doi:10.12068/j.issn.1005-3026.2022.11.006

东北大学学报（自然科学版） ›› 2022, Vol. 43 ›› Issue (11): 1561-1569.DOI: 10.12068/j.issn.1005-3026.2022.11.006

合金设计对贝氏体相变动力学影响的建模研究

李美莹¹，肖乃友¹，周剑华²，贾涛¹

(1. 东北大学轧制技术及连轧自动化国家重点实验室，辽宁沈阳110819； 2. 宝钢股份中央研究院，湖北武汉430080)

发布日期:2022-12-06
通讯作者: 李美莹
作者简介:李美莹 (1993-)，女，河南南阳人，东北大学博士研究生.
基金资助:
国家重点研发计划项目(2017YFB0304201，2016YFB0300603).

Modeling Research on Influence of Alloy Design on Bainite Transformation Kenitics

LI Mei-ying¹， XIAO Nai-you¹， ZHOU Jian-hua²， JIA Tao¹

1. State Key Laboratory of Rolling and Automation， Northeastern University， Shenyang 110819， China; 2. Central Research Institute of Baowu Co. Ltd.， Wuhan 430080， China.

Published:2022-12-06
Contact: JIA Tao
About author:-
Supported by:
-

摘要/Abstract

摘要： 采用基于形核控制机制的贝氏体等温相变动力学模型研究了合金设计对贝氏体相变动力学的影响.针对两种贝氏体高强钢，采用热膨胀仪在425~350℃开展了等温贝氏体相变实验，观察到了不同程度的贝氏体不完全相变现象.基于形核控制机制，采用切变型相变动力学模型对两种实验钢的贝氏体等温相变行为进行了建模研究，模型中同时考虑了晶界形核和自催化形核.最后，对比分析了两种实验钢中形核激活能、未转变奥氏体体积分数以及形核速率等的差异，为贝氏体高强钢的成分设计及工艺创新提供理论指导.

关键词: 贝氏体；等温相变；相变动力学；切变型相变机制；超高强钢

Abstract: A kinetic model of bainite isothermal transformation based on nucleation-controlled mechanism was used to study the effect of alloy design on bainite transformation kinetics. Using two kinds of high-strength bainite steels， isothermal bainite transformation experiments were conducted at 425~350℃ with a dilatometer. Different degrees of incomplete phase transformation phenomenon are observed. Based on nucleation-controlled mechanism， the displacive transformation kenetic model was used to describe the bainite isothermal transformation behavior of two experimental steels， where grain-boundary nucleation and autocatalytic nucleation were both considered. Finally， the difference in activation energy of nucleation， volume fraction of untransformed austenite and the nucleation rate etc between two experimental steels were comparatively analyzed， which provide theoretical guidance for the composition design and process innovation of high-strength bainite steel.

Key words: bainite; isothermal transformation; transformation kenitics; displacive mechanism; ultra-high strength steel

中图分类号:

TG142.1

李美莹，肖乃友，周剑华，贾涛. 合金设计对贝氏体相变动力学影响的建模研究[J]. 东北大学学报（自然科学版）, 2022, 43(11): 1561-1569.

LI Mei-ying， XIAO Nai-you， ZHOU Jian-hua， JIA Tao. Modeling Research on Influence of Alloy Design on Bainite Transformation Kenitics[J]. Journal of Northeastern University(Natural Science), 2022, 43(11): 1561-1569.

参考文献

[1]Lu X H，Yang Z H，Qian D S，et al.Effect of martensite pre-quenching on bainite transformation kinetics，martensite/bainite duplex microstructures，mechanical properties and retained austenite stability of GCr15 bearing steel ［J］.Journal of Materials Research and Technology，2021，15:2429-2438.
[2]Huang C C，Zou M Q，Qi L，et al.Effect of isothermal and pre-transformation temperatures on microstructure and properties of ultrafine bainitic steels ［J］.Journal of Materials Research and Technology，2021，12:1080-1090.
[3]Bhadeshia H K D H.Bainite in steels ［M］.2nd ed.Cambridge:IOM Communications Ltd，2001:129-135.
[4]Santofimia M J，Caballero F G，Capdevila C，et al.Evaluation of displacive models for bainite transformation kinetics in steels ［J］.Materials Transactions，2006，47(6):1492-1500.
[5]Van Bohemen S M C，Sietsma J.Modeling of isothermal bainite formation based on the nucleation kinetics ［J］.International Journal of Materials Research，2008，99(7):739-747.
[6]Van Bohemen S M C.Modeling start curves of bainite formation ［J］.Metallurgical and Materials Transactions A，2010，41(2):285-296.
[7]Sidhu G，Bhole S D，Chen D L，et al.An improved model for bainite formation at isothermal temperatures ［J］.Scripta Materialia，2011，64(1):73-76.
[8]Van Bohemen S M C，Hanlon D N.Comment on “an improved model for bainite formation at isothermal temperatures”［J］.Scripta Materialia，2011，65(4):371-372.
[9]Sidhu G，Bhole S D，Chen D L，et al.Reply to comments on “an improved model for bainite formation at isothermal temperatures”［J］.Scripta Materialia，2011，65(4):373-375.
[10]Van Bohemen S M C，Hanlon D N.A physically based approach to model the incomplete bainitic transformation in high-Si steels ［J］.International Journal of Materials Research，2012，103(8):987-991.
[11]Ravi A M，Sietsma J，Santofimia M J.Exploring bainite formation kinetics distinguishing grain-boundary and autocatalytic nucleation in high and low-Si steels ［J］.Acta Materialia，2016，105:155-164.
[12]Ravi A M，Sietsma J，Santofimia M J.Bainite formation kinetics in steels and the dynamic nature of the autocatalytic nucleation process ［J］.Scripta Materialia，2017，140:82-86.
[13]Ravi A M，Navarro-López A，Sietsma J，et al.Influence of martensite/austenite interfaces on bainite formation in low-alloy steels below M_s［J］.Acta Materialia，2020，188:394-405.
[14]Samanta S，Biswas P，Giri S，et al.Formation of bainite below the M temperature:kinetics and crystallography ［J］.Acta Materialia，2016，105(15):390-403.
[15]Liu C，Liu Y，Zhang D，et al.Bainite formation kinetics during isothermal holding in modified high Cr ferritic steel ［J］.Metallurgical and Materials Transactions A，2013，44(12):5447-5455.
[16]Liu C，Shi L，Liu Y，et al.Acicular ferrite formation during isothermal holding in HSLA steel ［J］.Journal of Materials Science，2016，51(7):3555-3563.
[17]Van Bohemen S M C.Bainite and martensite start temperature calculated with exponential carbon dependence ［J］.Materials Science and Technology，2012，28(4):487-495.
[18]Fielding L C D.The bainite controversy ［J］.Materials Science and Technology，2013，29(4):383-399.
[19]Swallow E，Bhadeshia H K D H.High resolution observations of displacements caused by bainitic transformation ［J］.Materials Science and Technology，1996，12(2):121-125.
[20]Bhadeshia H K D H，Edmonds D V.The mechanism of bainite formation in steels ［J］.Acta Materialia，1980，28(9):1265-1273.
[21]University of Cambridge.Materials Algorithms Project(MAP)［EB/OL］.［2015-12-01］.http://www.msm.cam.ac.uk/map/.
[22]Peng F，Xu Y B，Han D T，et al.Kinetic models of multiple-stage martensite transformation and subsequent isothermal bainite formation excluding ε-carbide precipitation in intercritical quenching and partitioning steels ［J］.Materials Design，2019，183(5):1-12.
[23]刘宗昌，任慧平.贝氏体与贝氏体相变［M］.北京:冶金工业出版社，2009:198.(Liu Zong-chang，Ren Hui-ping.Bainite and bainite transformation［M］.Beijing:Metallurgical Industry Press，2009:198.)
[24]Kang M，Zhang M X，Liu F，et al.Kinetics and morphology of isothermal transformations at intermediate temperature in 15CrMnMoV steel ［J］.Materials Transactions，2009，50(1):123-129.
[25]Olson G B，Cohen M.A general mechanism of martensitic nucleation:Part II.FCC→BCC and other martensitic transformations ［J］.Metallurgical and Materials Transactions A，1976，7(11):1905-1914.

合金设计对贝氏体相变动力学影响的建模研究

Modeling Research on Influence of Alloy Design on Bainite Transformation Kenitics

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周晓光，王铎，张东航，刘振宇. ESP工艺下低碳钢奥氏体演变行为[J]. 东北大学学报（自然科学版）, 2021, 42(1): 37-43.
[2]	王明明，高秀华，杜林秀，张大征. V-N微合金化X80抗大变形管线钢的组织与力学性能[J]. 东北大学学报:自然科学版, 2020, 41(6): 801-806.
[3]	辛博，周显新，巩亚东. 变厚度熔覆层沉积成形工艺与性能研究[J]. 东北大学学报:自然科学版, 2020, 41(3): 374-379.
[4]	张大征，高秀华，杜林秀，王鸿轩. 多级热处理对柔性立管用高强钢组织性能影响[J]. 东北大学学报:自然科学版, 2020, 41(1): 49-54.
[5]	董春宇，赵宪明，周晓光，赵景莉. 冷却工艺参数对海洋工程用H型钢组织性能的影响[J]. 东北大学学报:自然科学版, 2019, 40(4): 478-482.
[6]	王学强，赵金华，袁国，王国栋. 超快冷下X65管线钢微观组织演变及强化机制分析[J]. 东北大学学报:自然科学版, 2019, 40(3): 334-339.
[7]	吴俊宇，王斌，王丙兴，王昭东. 轧制道次间插入冷却对特厚钢板组织与性能的影响[J]. 东北大学学报:自然科学版, 2018, 39(11): 1582-1587.
[8]	周晓光，陈其源，刘振宇，吴思炜. Ti微合金化汽车大梁钢510L动态再结晶行为[J]. 东北大学学报:自然科学版, 2018, 39(5): 624-629.
[9]	王鹤松，袁国，曹光明，王国栋. 双辊薄带连铸低碳微合金钢的铸态组织[J]. 东北大学学报:自然科学版, 2018, 39(4): 497-500.
[10]	陈其源，周晓光，刘振宇，吴思炜. Ti微合金化汽车大梁钢510L的组织性能[J]. 东北大学学报:自然科学版, 2018, 39(3): 339-344.
[11]	宁方坤，贾伟涛，朱伏先，王平. P91厚壁钢管混晶组织分析[J]. 东北大学学报:自然科学版, 2018, 39(1): 50-55.
[12]	叶其斌，谢谦，刘振宇，王国栋. 超快冷工艺对钢板心部异常带状组织的抑制作用[J]. 东北大学学报:自然科学版, 2017, 38(12): 1696-1701.
[13]	周晓光，郭洪河，蒋小冬，刘振宇. Ti微合金化Q390高强钢热变形行为研究[J]. 东北大学学报:自然科学版, 2017, 38(12): 1702-1706.
[14]	李兴，陈礼清. 奥氏体化温度对Fe-17Mn-0.05C钢组织和拉伸性能的影响[J]. 东北大学学报:自然科学版, 2017, 38(8): 1084-1087.
[15]	利成宁，袁国，康健，王国栋. 异步热轧对低合金钢显微组织及力学性能的影响[J]. 东北大学学报:自然科学版, 2017, 38(7): 941-945.