东北大学学报（自然科学版）

东北大学学报:自然科学版 ›› 2016, Vol. 37 ›› Issue (10): 1446-1450.DOI: 10.12068/j.issn.1005-3026.2016.10.017

• 机械工程 • 上一篇    下一篇

扭转精度对扭杆弹簧强扭工艺的影响

王振峰， 董明明， 赵凯， 顾亮   

  1. (北京理工大学 机械与车辆学院， 北京100081)
  • 收稿日期:2015-06-10 修回日期:2015-06-10 出版日期:2016-10-15 发布日期:2016-10-14
  • 通讯作者: 王振峰
  • 作者简介:王振峰(1987-)，男，河南新乡人，北京理工大学博士研究生； 顾亮(1957-)男，山东淄博人，北京理工大学教授，博士生导师.
  • 基金资助:
    国家部委基金资助项目 (1030020220707).

Effect of Torsion Precision on Torsion Bar Spring Pre-setting Process

WANG Zhen-feng， DONG Ming-ming， ZHAO Kai， GU Liang   

  1. School of Mechanical and Vehicle Engineering， Beijing Institute of Technology， Beijing 100081，China.
  • Received:2015-06-10 Revised:2015-06-10 Online:2016-10-15 Published:2016-10-14
  • Contact: GU Liang
  • About author:-
  • Supported by:
    -

RichHTML

0

PDF (PC)

818

摘要： 为了研究扭杆弹簧扭转精度对其强扭过程的影响，利用弹塑性理论对扭杆弹簧强扭过程进行了理论探讨，获得扭杆弹簧在屈服与塑性强扭工况下的断面应力、扭矩及残余应力等变化的数学模型.应用ABAQUS有限元软件对不同型号、强扭工况的扭杆弹簧进行数值模拟，分析了扭转精度对扭杆弹簧强扭效果的影响.结果表明，在强扭工艺允许范围内，扭转误差对扭杆弹簧强扭效果影响不超过5%.试验结果不仅验证了有限元模型的正确性，也得出扭杆弹簧强扭误差在不超过±1°工况下的强扭效果可近似等同的结论，此研究为扭杆弹簧强扭工艺的完善提供理论依据.

关键词: 扭杆弹簧, 弹塑性, 强扭工艺, 数值模拟, 强扭试验

Abstract: In order to study the effect of torsion precision on pre-setting process， the elastic-plastic theory was used to discuss the pre-setting process of torsion bar spring. Then， a mathematical model changing with stress， torque and residual stress was obtained under yield pre-setting and plasticity pre-setting situation. The ABAQUS software was used to simulate torsion bar spring with different models and pre-setting situations， and the effect of pre-setting precision on torsion bar spring was analyzed. The results showed that the effect of torsion bar spring pre-setting process in the range of torsion error on pre-setting is less than 5%. The test data not only validates correctness of the finite element model， but shows that torsion bar spring with no more than ±1° pre-setting error can be seen approximately equivalent. The results provide a theoretical reference for improving the process of torsion bar spring pre-setting.

Key words: torsion bar spring, elastic-plastic, pre-setting process, numerical simulation, pre-setting test

中图分类号: