钛合金激光熔丝增材制造的温度场与应力场模拟

doi:10.12068/j.issn.1005-3026.2020.04.017

东北大学学报:自然科学版 ›› 2020, Vol. 41 ›› Issue (4): 551-556.DOI: 10.12068/j.issn.1005-3026.2020.04.017

钛合金激光熔丝增材制造的温度场与应力场模拟

任朝晖，刘振，周世华，段景曦

(东北大学机械工程与自动化学院，辽宁沈阳110819)

收稿日期:2019-05-18 修回日期:2019-05-18 出版日期:2020-04-15 发布日期:2020-04-17
通讯作者: 任朝晖
作者简介:任朝晖(1968-)，男，辽宁沈阳人，东北大学教授，博士生导师.
基金资助:
国家重点研发计划项目(2017YFB1103700); 国家自然科学基金资助项目(51475084).

Temperature Field and Stress Field Simulation of Titanium Alloy Laser Fuse Additive Manufacturing

REN Zhao-hui， LIU Zhen， ZHOU Shi-hua， DUAN Jing-xi

School of Mechanical Engineering & Automation， Northeastern University， Shenyang 110819， China.

Received:2019-05-18 Revised:2019-05-18 Online:2020-04-15 Published:2020-04-17
Contact: REN Zhao-hui
About author:-
Supported by:
-

摘要/Abstract

摘要： 激光熔丝增材成形过程中复杂热循环和残余应力分布会使沉积层产生较大的变形甚至开裂.利用ABAQUS软件建立其完全热力耦合有限元模型，采用移动热源子程序模拟激光加载，生死单元技术模拟材料的添加.综合考虑了材料的熔化潜热、对流/辐射换热边界条件、随温度变化的材料非线性等问题，研究Ti-6Al-4V 钛合金单道多层薄壁件沉积过程中的热循环特性和残余应力分布.结果表明:沉积成形经历了快速加热、快速冷却的过程，随着层数的增加，热累积效应增强；沉积层整体呈拉应力状态，易产生裂纹等缺陷.

关键词: 激光熔丝增材, 温度场, 残余应力, Ti-6Al-4V钛合金, 完全热力耦合

Abstract: Complex thermal cycling and residual stress distribution during the laser fuse additive forming can cause large deformation or even cracking of the deposited layer. ABAQUS software was used to establish a fully thermo-mechanical coupled finite element model. The mobile heat source subroutine was used to simulate laser loading， and the life-and-death unit technology was used to simulate the addition of materials. The thermal cycle characteristics and residual stress distribution of Ti-6Al-4V titanium alloy’s single-channel multi-layer thin-walled parts during the deposition were studied by considering the latent heat of fusion， convective/radiation heat transfer boundary conditions and material nonlinearity with temperature. The results showed that the deposition process has experienced the rapid heating and rapid cooling. With the increase of the number of layers， the thermal accumulation effect is enhanced. The sedimentary layer is in the tensile stress state and is prone to cracks and other defects.

Key words: laser fuse additive, temperature field, residual stress, Ti-6Al-4V titanium alloy, fully thermal-mechanical coupling

中图分类号:

TG457.19

任朝晖，刘振，周世华，段景曦. 钛合金激光熔丝增材制造的温度场与应力场模拟[J]. 东北大学学报:自然科学版, 2020, 41(4): 551-556.

REN Zhao-hui， LIU Zhen， ZHOU Shi-hua， DUAN Jing-xi. Temperature Field and Stress Field Simulation of Titanium Alloy Laser Fuse Additive Manufacturing[J]. Journal of Northeastern University Natural Science, 2020, 41(4): 551-556.

参考文献

[1]王华明，张述泉，王向明.大型钛合金结构件激光直接制造的进展与挑战［J］.中国激光，2009，36(12):3204-3209.(Wang Hua-ming，Zhang Shu-quan，Wang Xiang-ming.Progress and challenges of laser direct manufacturing of large titanium structural components［J］.Chinese Journal Lasers，2009，36(12):3204-3209.)
[2]Szost B A，Terzi S，Martina F，et al.A comparative study of additive manufacturing techniques:residual stress and microstructural analysis of CLAD and WAAM printed Ti-6Al-4V components［J］.Materials and Design，2016，89:559-567.
[3]Montevecchi F，Grossi N，Takagi H，et al.Cutting forces analysis in additive manufactured AISI H13 alloy［J］.Procedia CIRP，2016，46:476-479.
[4]王福雨，刘伟军，赵宇辉，等.复杂薄壁零件激光快速成形过程的热力耦合场数值模拟［J］.机械工程学报，2013，49(5):191-198.(Wang Fu-yu，Liu Wei-jun，Zhao Yu-hui，et al.Thermo-mechanical coupling field simulation of complex thin-wall part laser rapid prototype process［J］.Journal of Mechanical Engineering，2013，49(5):191-198.)
[5]Montevecchi F，Venturini G，Scippa A，et al.Finite element modeling of wire-arc-additive-manufacturing process［J］.Procedia CIRP，2016，55:109-114.
[6]Fu C H，Guo Y B.Three-dimensional temperature gradient mechanism in selective laser melting of Ti-6Al-4V［J］.Journal of Manufacturing Science and Engineering，2014，136(6):1-7.
[7]Zhao H，Zhang G，Yin Z，et al.A 3D dynamic analysis of thermal behavior during single-pass multi-layer weld-based rapid prototyping［J］.Journal of Materials Processing Technology，2011，211(3):488-495.
[8]Zhao H，Zhang G，Yin Z，et al.Three-dimensional finite element analysis of thermal stress in single-pass multi-layer weld-based rapid prototyping［J］.Journal of Materials Processing Technology，2012，212(1):276-285.
[9]戴德平，蒋小华，蔡建鹏，等.激光熔覆Incone 1718镍基合金温度场与应力场模拟［J］.中国激光，2015，42(9):1-8.(Dai De-ping，Jiang Xiao-hua，Cai Jian-peng，et al.Numerical simulation of temperature field and stress distribution in Incone 1718 Ni base alloy induced by laser cladding［J］.Chinese Journal of Lasers，2015，42(9):1-8.)
[10]Ali H，Ghadbeigi H，Mumtaz K.Effect of scanning strategies on residual stress and mechanical properties of selective laser melted Ti6Al4V［J］.Materials Science and Engineering A，2017，712:175-187.
[11]逯世杰，郑乔，张超华，等.不同有限元软件对Q390钢厚板T型接头焊接残余应力和变形预测精度与计算效率的比较［J］.机械工程学报，2019，55(6):11-22.(Lu Shi-jie，Zheng Qiao，Zhang Chao-hua，et al.A comparative study on computational accuracy and efficiency of welding residual stress and deformation in a Q390 steel thick plate T joint among three kinds of different FEM software［J］.Journal of Mechanical Engineering，2019，56(6):11-22.)
[12]李慧敏.激光熔丝增材制造工艺特性研究［D］.重庆:重庆大学，2017.(Li Hui-min.Study on the process characteristics of wire based laser additive manufacturing［D］.Chongqing:Chongqing University，2017.)
[13]Hao M，Sun Y.A FEM model for simulating temperature field in coaxial laser cladding of Ti6AL4V alloy using an inverse modeling approach［J］.International Journal of Heat and Mass Transfer，2013，64:352-360.
[14]Goldak J，Chakravarti A，Bibby M.A new finite-element model for welding heat-sources［J］.Metallurgical Transactions B—Process Metallurgy，1984，15(2):299-305.
[15]Edwards P，O’Conner A，Ramulu M.Electron beam additive manufacturing of titanium components: properties and performance［J］.Journal of Manufacturing Science and Engineering，2013，135(6):1-7.
[16]Liang W，Murakawa H，Deng D.Investigation of welding residual stress distribution in a thick-plate joint with an emphasis on the features near weld end-start［J］.Materials and Design，2015，67:303-312.
[17]Parry L，Ashcroft I A，Wildman R D.Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation［J］.Additive Manufacturing，2016，12:1-15.
[15]关守平，房少纯.一种新型的区间-粒子群优化算法［J］.东北大学学报(自然科学版)，2012，33(10):1381-1384.(Guan Shou-ping，Fang Shao-chun.A new interval particle swarm optimization algorithm［J］.Journal of Northeastern University(Natural Science)，2012，33(10):1381-1384.)

钛合金激光熔丝增材制造的温度场与应力场模拟

Temperature Field and Stress Field Simulation of Titanium Alloy Laser Fuse Additive Manufacturing

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	任朝晖，王云贺，李竺鸿，王琛. 增材-微锻造加工工艺应力场数值模拟研究[J]. 东北大学学报（自然科学版）, 2022, 43(6): 881-887.
[2]	赵永，赵乾百，王述红，李友明. 不同温度场下断层黏滑失稳过程模拟[J]. 东北大学学报（自然科学版）, 2022, 43(10): 1453-1460.
[3]	张东祥，郭立新. 汽车驱动桥壳焊接变形及焊接残余应力有限元仿真分析[J]. 东北大学学报（自然科学版）, 2021, 42(5): 700-705.
[4]	冯莹莹，赵双，刘照松，骆宗安. 7075铝合金搅拌摩擦焊模拟与实验研究[J]. 东北大学学报（自然科学版）, 2021, 42(3): 340-346.
[5]	王宁，李宝宽，齐凤升，张晓明. 蝶式感应加热中间包流场与升温特性[J]. 东北大学学报（自然科学版）, 2021, 42(12): 1724-1730.
[6]	李彦龙，吴琼，秦晓峰，刘常升. Cr5支承辊接触疲劳损伤及其次表层组织变化[J]. 东北大学学报:自然科学版, 2020, 41(6): 818-823.
[7]	牛艺静，孙聪，庞刚，修世超. 预应力时效性对磨削强化表面应力的影响[J]. 东北大学学报:自然科学版, 2020, 41(4): 546-550.
[8]	杨玉莹，巩亚东，屈硕硕，蔡明. 增/减材复合加工316L宏观形貌和残余应力试验[J]. 东北大学学报:自然科学版, 2020, 41(3): 380-386.
[9]	兰亮云，邵国庆，张一婷，王艺南. 焊接顺序对Q690钢T型接头残余应力和变形的影响[J]. 东北大学学报:自然科学版, 2020, 41(12): 1741-1746.
[10]	夏毅敏，仝磊，柏彬，华伟明. 盾构切刀硬质合金与钢基体钎焊残余应力[J]. 东北大学学报:自然科学版, 2020, 41(1): 101-107.
[11]	李朕均，赵春雨，闻邦椿，卢泽宸. 数控机床进给系统热源发热率辨识与热误差预测[J]. 东北大学学报:自然科学版, 2019, 40(9): 1305-1309.
[12]	尹国强，巩亚东，李雨晴，宋俊利. 新型点磨削砂轮磨削表面/亚表面质量研究[J]. 东北大学学报:自然科学版, 2019, 40(6): 835-840.
[13]	任朝晖，刘振，张小双，张兴文. 超声微锻造辅助激光熔丝增材制造数值模拟研究[J]. 东北大学学报:自然科学版, 2019, 40(11): 1590-1595.
[14]	柯迪文，刘相华，支颖. 双相钢差厚板退火过程的温度场[J]. 东北大学学报:自然科学版, 2018, 39(8): 1118-1122.
[15]	郑迪，王大志，李硕，于林鑫. 基于电磁-温度耦合方法的永磁驱动器温度场分析[J]. 东北大学学报:自然科学版, 2018, 39(4): 457-461.