碳化钨涂层高温摩擦磨损行为

doi:10.12068/j.issn.1005-3026.2014.06.022

东北大学学报:自然科学版 ›› 2014, Vol. 35 ›› Issue (6): 858-861.DOI: 10.12068/j.issn.1005-3026.2014.06.022

碳化钨涂层高温摩擦磨损行为

闫玉涛，廉巨龙，徐元军，孙志礼

(东北大学机械工程与自动化学院，辽宁沈阳110819)

收稿日期:2013-08-23 修回日期:2013-08-23 出版日期:2014-06-15 发布日期:2014-04-11
通讯作者: 闫玉涛
作者简介:闫玉涛(1970-)，男，吉林磐石人，东北大学副教授，博士;孙志礼(1957-)，男，山东巨野人，东北大学教授，博士生导师.
基金资助:
航空科学基金资助项目(20120450001).

Friction and Wear Behaviors of WC Coatings at High Temperature

YAN Yutao， LIAN Julong， XU Yuanjun， SUN Zhili

School of Mechanical Engineering & Automation， Northeastern University， Shenyang 110819， China.

Received:2013-08-23 Revised:2013-08-23 Online:2014-06-15 Published:2014-04-11
Contact: YAN Yutao
About author:-
Supported by:
-

摘要/Abstract

摘要： 采用爆炸喷涂技术制备了碳化钨涂层，利用HT-1000高温摩擦磨损试验机研究了碳化钨涂层高温下摩擦磨损性能，通过扫描电子显微镜和X射线衍射分析了涂层磨损表面形貌、元素分布和相结构.结果表明:碳化钨涂层由雪花片状颗粒堆叠而成，如山地状，结合紧密.定温条件下，摩擦因数随着试验温度升高而减小，试验温度为550℃时，摩擦因数最小；磨损量随着温度升高而增大，550℃时，磨损量由于配副材料的转移出现了负增加.温度低于350℃时，磨损表面具有撕裂、轻微黏着和磨粒磨损痕迹；在550℃时，磨损表面发生了剥落、严重黏着和氧化磨损.连续升温条件下，温度低于300℃时，摩擦因数较小，在350~550℃范围内，摩擦因数波动较大；磨损表面以剥层、黏着和氧化磨损为主.

关键词: 碳化钨涂层, 摩擦因数, 高温, 连续升温, 磨损机理

Abstract: The WC coatings were prepared by the detonation gun spray technique. Their tribological properties at high temperature were investigated on a HT-1000 high temperature friction/wear tester. The worn surface and element distribution were analyzed by scanning electronic microscope(SEM). The phase structure was analyzed by Xray diffraction. The results show that the WC coatings， heaped by the snowflakelike particles， are of the mountain ground shape. The bonding interface is very tight. Under definite temperature， the friction coefficient gradually minishes with the temperature increase， and the minimum is achieved at 550℃. The wear mass loss increases as the temperature increases， with minus addition appearing at 550℃ because of the material transfer. The worn surface shows laceration， slight adhesive wear and abrasive wear below 350℃. However， the wear mechanism is the combination of desquamation， severe adhesive wear and oxidization wear at 550℃. With the continuous temperature increase， the friction coefficient is balanced and lessens below 300℃，which is larger and shows bigger fluctuation within the temperature range from 350℃ to 550℃. The worn surface shows desquamation， adhesive wear and oxidation wear.

Key words: WC coatings, friction coefficient, high temperature, continuous heatingup, wear mechanism

中图分类号:

TH1171

闫玉涛，廉巨龙，徐元军，孙志礼. 碳化钨涂层高温摩擦磨损行为[J]. 东北大学学报:自然科学版, 2014, 35(6): 858-861.

YAN Yutao， LIAN Julong， XU Yuanjun， SUN Zhili. Friction and Wear Behaviors of WC Coatings at High Temperature[J]. Journal of Northeastern University Natural Science, 2014, 35(6): 858-861.

参考文献

[1] 杨德明.爆炸喷涂碳化钨涂层工艺及性能研究［D］.大连:大连海事大学，2009.(Yang Deming.An investigation in processes and properties of detonation gun sprayed WC coatings［D］.Dalian:Dalian Maritime University，2009.)
[2] Guo J，Xu B S，Wang H D，et al.Characterization of WC/Co coatings on metal substrates［J］.Materials Letters，2007，61(11/12):2454/2456.
[3] Guilemany J M，Miguel J M，Vizcaino S，et al.Role of threebody abrasion wear in the sliding wear behavior of WC/Co coatings obtained by thermal spraying［J］.Surface and Coatings Technology，2001，140(2):141/146.
[4] Kumari K，Anand K，Bellacci M，et al.Effect of microstructure on abrasive wear behavior of thermally sprayed WC/10Co/4Cr coatings［J］.Wear，2010，268(11/12):1309/1319.
[5] Yang Q Q，Senda T，Obmori A.Effect of carbide grain size on microstructure and sliding wear behavior of HVOFsprayed WC/12% Co coatings［J］.Wear，2002，254(1):23/24.
[6] Liao H，Normand B，Coddet C.Influence of coating microstructure on the abrasive wear resistance of WC/Co cermet coatings［J］.Surface and Coatings Technology，2000，124(2/3):235/242.
[7] Liu H W，Xu X J，Zhu M H，et al.High temperature fretting wear behavior of WC/25Co coatings prepared by Dgun spraying on Ti/Al/Zr titanium alloy［J］.Tribology International，2011，44(11):1461/1470.
[8] Maiti A K，Mukhopadhyay N，Raman R.Effect of adding WC powder to the feedstock of WC/Co/Cr based HVOF［J］.Surface and Coatings Technology，2007，201(18):7781/7788.
[9] Alexander A B，Sergey A P，Alexey V Z.Influence of carbon content of WC/Co electrode materials on the wear resistance of electrospark coatings［J］.Journal of Surface Engineered Materials and Advanced Technology，2012，2(2):65/70.

[1]	贾蓬，李博，祝鹏程，王琦伟. 单轴受压高温损伤砂岩的电学响应特征[J]. 东北大学学报（自然科学版）, 2023, 44(4): 558-564.
[2]	朱煜，宋巍，梁静静，李金国. Al元素对一种增材制造镍基高温合金显微组织和拉伸行为的影响[J]. 东北大学学报（自然科学版）, 2023, 44(3): 348-356.
[3]	贾蓬，祝鹏程，李博，毛松泽. 热损伤大理岩波动特征及声发射特性试验研究[J]. 东北大学学报（自然科学版）, 2023, 44(2): 279-288.
[4]	陈猛，曹宇新，王瑜婷. 工程水泥基复合材料高温损伤超声特性[J]. 东北大学学报（自然科学版）, 2022, 43(11): 1638-1643.
[5]	王皓，曹光明，汤军舰，刘振宇. 700MPa级高强钢水蒸气条件下的高温氧化行为[J]. 东北大学学报（自然科学版）, 2021, 42(7): 920-926.
[6]	吴雅菊，许开立，王若菌，徐晓虎. 高温熔融金属作业安全完整性评价[J]. 东北大学学报（自然科学版）, 2021, 42(4): 576-581.
[7]	张洪伟，张通，万志军，周长冰. 高温高压下岩石水力压裂实验新型封隔技术[J]. 东北大学学报（自然科学版）, 2021, 42(3): 422-428.
[8]	董硕，沙松，蒙世仟，荣冠. 液氮冷却作用下三类高温岩石力学性能试验研究[J]. 东北大学学报（自然科学版）, 2021, 42(11): 1591-1599.
[9]	刘干，宁新禹，李天祥，李海军. 车轴钢高温黏塑性本构模型及流变行为分析[J]. 东北大学学报（自然科学版）, 2021, 42(10): 1407-1414.
[10]	田勇，安小雪，王昭东，王国栋. 12Cr2Ni4A钢高温真空低压脉冲渗碳工艺[J]. 东北大学学报:自然科学版, 2020, 41(9): 1251-1256.
[11]	巩亚东，苏志朋，孙瑶，金丽雅. 镍基单晶高温合金微磨削形貌仿真及实验研究[J]. 东北大学学报:自然科学版, 2020, 41(7): 949-954.
[12]	曹光明，高欣宇，单文超，潘帅. Ni系低温钢的高温氧化行为研究[J]. 东北大学学报:自然科学版, 2020, 41(6): 792-800.
[13]	郭快快，商硕，陈进，刘常升. 数值模拟雾化气压对GH4169合金粉末粒径的影响[J]. 东北大学学报:自然科学版, 2020, 41(6): 807-811.
[14]	巩亚东，张伟健，蔡明，周显新. 镍基单晶高温合金磨削变质层工艺试验研究[J]. 东北大学学报:自然科学版, 2020, 41(6): 846-851.
[15]	巩亚东，孟凡涛，孙瑶，于兴晨. 镍基单晶高温合金的微孔加工对比实验研究[J]. 东北大学学报:自然科学版, 2020, 41(1): 84-89.

碳化钨涂层高温摩擦磨损行为

Friction and Wear Behaviors of WC Coatings at High Temperature

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价