东北大学学报（自然科学版）

东北大学学报:自然科学版 ›› 2018, Vol. 39 ›› Issue (4): 506-511.DOI: 10.12068/j.issn.1005-3026.2018.04.011

• 材料与冶金 • 上一篇    下一篇

激光重熔高速电弧喷涂FeNiCrAl涂层的组织与断裂韧性

盛忠起1， 周静1,2， 胡岚1， 魏世丞2   

  1. (1. 东北大学 机械工程与自动化学院， 辽宁 沈阳110819; 2. 陆军装甲兵学院 装备再制造技术国防科技重点实验室， 北京100072)
  • 收稿日期:2016-09-04 修回日期:2016-09-04 出版日期:2018-04-15 发布日期:2018-04-10
  • 通讯作者: 盛忠起
  • 作者简介:盛忠起(1972-)，男，山东宁津人，东北大学副教授； 魏世丞(1974-)，男，辽宁沈阳人，陆军装甲兵学院教授.
  • 基金资助:
    国家自然科学基金资助项目(51171041).国家自然科学基金优秀青年科学基金资助项目(51222510).

Microstructure and Fracture Toughness of Laser Remelting Treatment on FeNiCrAl Coating by High-Velocity Arc Spraying

SHENG Zhong-qi1， ZHOU Jing1,2， HU Lan1， WEI Shi-cheng2   

  1. 1. School of Mechanical Engineering & Automation， Northeastern University， Shenyang 110819， China; 2. National Key Laboratory for Remanufacturing， Academy of Army Armored Forces， Beijing 100072， China.
  • Received:2016-09-04 Revised:2016-09-04 Online:2018-04-15 Published:2018-04-10
  • Contact: SHENG Zhong-qi
  • About author:-
  • Supported by:
    -

RichHTML

0

PDF (PC)

784

摘要： 采用激光技术对高速电弧喷涂FeNiCrAl涂层进行重熔处理.分析了重熔前后涂层的组织结构、物相成分、显微硬度与断裂韧性.结果表明:重熔后，喷涂层片层状堆叠结构与孔隙得到消除，组织结构变得均匀、致密，涂层与基体由机械结合变为冶金结合.喷涂层物相主要有α-Fe及金属间化合物AlFe3，AlFe和Al0.4Fe0.6，重熔后，生成了新相Fe-Cr，［Fe， Ni］固溶体和碳化物NiC○x.重熔后涂层的平均显微硬度为7.79GPa，约为基体硬度(2.5GPa)的3倍，约为喷涂层硬度(6.0GPa)的1.3倍.载荷为4.9，9.8N时，喷涂层的压痕尖头出现裂纹，涂层平均断裂韧性为1.20MPa·m1/2，载荷为2.94~9.8N时，重熔后涂层的压痕尖头均没有观察到裂纹.

关键词: 激光重熔, 高速电弧喷涂, FeNiCrAl涂层, 组织结构, 断裂韧性

Abstract: Remelting treatment of FeNiCrAl coating deposited by high-velocity arc spraying was conducted using laser technology. The microstructure， phase composition， microhardness and fracture toughness of the coating before and after remelting were analyzed. The results showed that the layer stack structure and pores of the spraying coating were eliminated， the microstructure of the coating became uniform and dense， and the interaction between the coating and the substrate were changed from mechanical combination to metallurgical bonding after remelting. Compared with the phases of the spraying coating， which consisted of α-Fe and intermetallic compounds， such as AlFe3， AlFe and Al0.4Fe0.6， three more phases could be observed after remelting， which were a new phase of Fe-Cr， the solid solution of ［Fe， Ni］ and carbide NiC○x. The average microhardness of the coating after remelting was 7.79GPa， which was about 3 times than that of the substrate (2.5GPa) and about 1.3 times than that of the spraying coating (6.0GPa). In the indentation test of the spraying coating， the indentation cracks appeared at the loads of 4.9 and 9.8N， corresponding to the average fracture toughness of spraying coating of 1.20MPa·m1/2， while no crack was found during loading of 2.94~9.8N after remelting.

Key words: laser remelting, high-velocity arc spraying, FeNiCrAl coating, microstructure, fracture toughness

中图分类号: