东北大学学报（自然科学版）

东北大学学报（自然科学版） ›› 2022, Vol. 43 ›› Issue (1): 65-70.DOI: 10.12068/j.issn.1005-3026.2022.01.009

• 机械工程 • 上一篇    下一篇

熔丝成型薄板拉伸性能的理论与实验研究

姜世杰1,2， 董天阔1， 戴卫兵1， 战明3   

  1. )(1. 东北大学 机械工程与自动化学院， 辽宁 沈阳110819; 2. 辽宁省机械装备动力学可靠性重点实验室， 辽宁 沈阳110819; 3. 东北大学 信息科学与工程学院， 辽宁 沈阳110819)
  • 修回日期:2021-01-07 接受日期:2021-01-07 发布日期:2022-01-25
  • 通讯作者: 姜世杰
  • 作者简介:姜世杰(1985-)，男，辽宁营口人，东北大学副教授.
  • 基金资助:
    国家自然科学基金资助项目(51705068)； 中央高校基本科研业务费专项资金资助项目(N180703009，N170302001).

Theoretical and Experimental Study on Tensile Properties of Fused Filament Fabrication Thin Plates

JIANG Shi-jie1,2， DONG Tian-kuo1， DAI Wei-bing1， ZHAN Ming3   

  1. 1. School of Mechanical Engineering & Automation， Northeastern University， Shenyang 110819， China; 2. Key Laboratory of Dynamics Reliability of Mechanical Equipment， Shenyang 110819， China; 3. School of Information Science & Engineering， Northeastern University， Shenyang 110819， China.
  • Revised:2021-01-07 Accepted:2021-01-07 Published:2022-01-25
  • Contact: JIANG Shi-jie
  • About author:-
  • Supported by:
    -

RichHTML

1

PDF (PC)

133

摘要： 由于熔丝成型(fused filament fabrication，FFF)技术逐层沉积的制造工艺特点，其产品的拉伸性能存在着明显的局限性.为了能够提出切实有效的改进措施，需要明确FFF产品相应的机理，即建立本构关系理论模型.基于经典弹性力学理论，对FFF薄板试件的本构关系进行了理论建模，完成了试件拉伸性能的解析研究;然后利用拉伸实验机获得了试件拉伸性能的实验结果;最后，分别将X和Z方向打印试件的理论与实验的应力-应变曲线结果相对比，发现二者吻合度较好，验证了理论模型的正确性与准确性.

关键词: 熔丝成型;拉伸性能;本构模型;应力-应变;拉伸实验

Abstract: Due to the manufacturing layer-by-layer deposition process of the fused filament fabrication (FFF) technology， the tensile properties of the products have obvious limitations. In order to put forward effective improvement measures， the corresponding mechanism of FFF products should be clarified， that is， establishing theoretical constitutive model. Based on the classical elastic mechanics theory， the constitutive model of FFF thin plate samples is set up， and the theoretical analysis on the tensile properties of the samples are completed. Then， the experimental tensile properties of the samples were obtained by using the tensile testing machine.Finally， by comparing the theoretical and experimental results of stress-strain curves of the samples built in both X and Z direction， it is shown that they are in good consistence， verifying the correctness and accuracy of the theoretical model.

Key words: fused filament fabrication (FFF); tensile property; constitutive model; stress-strain; tensile test

中图分类号: