碳纤维复合材料螺旋铣孔瞬时切削力系数识别

doi:10.12068/j.issn.1005-3026.2020.10.011

东北大学学报:自然科学版 ›› 2020, Vol. 41 ›› Issue (10): 1432-1437.DOI: 10.12068/j.issn.1005-3026.2020.10.011

碳纤维复合材料螺旋铣孔瞬时切削力系数识别

王海艳，王健宇，陶克新

(东北大学秦皇岛分校控制工程学院，河北秦皇岛066004)

收稿日期:2019-10-10 修回日期:2019-10-10 出版日期:2020-10-15 发布日期:2020-10-20
通讯作者: 王海艳
作者简介:王海艳(1973-)，女，河北秦皇岛人，东北大学副教授.
基金资助:
国家自然科学基金资助项目(51705070)；河北省自然科学基金资助项目(E2020501014).

Identification of Instantaneous Cutting Force Coefficients for Helical Milling of Carbon Fiber Composite Materials

WANG Hai-yan， WANG Jian-yu， TAO Ke-xin

School of Control Engineering， Northeastern University at Qinhuangdao， Qinhuangdao 066004， China.

Received:2019-10-10 Revised:2019-10-10 Online:2020-10-15 Published:2020-10-20
Contact: WANG Hai-yan
About author:-
Supported by:
-

摘要/Abstract

摘要： 在螺旋铣孔过程中，刀具绕其自身轴线自转的基础上围绕预加工孔中心公转并保持轴向进给.为了准确预测碳纤维增强复合材料(CFRP)螺旋铣孔过程中的切削力，基于螺旋铣孔的基本切削机理，考虑刀具侧刃和底刃在进给过程中对切削过程的影响及复合材料的各向异性特征，构建螺旋铣孔过程中切削力解析模型.根据全因子条件下复合材料螺旋铣孔试验数据，采用数据拟合方法识别底刃切削力系数，采用瞬时切削力方法识别侧刃切削力系数.结果表明仿真切削力能够较好地拟合试验值.

关键词: 螺旋铣孔, 碳纤维增强复合材料, 切削力, 瞬时切削力系数, 切削试验

Abstract: The special tool orbits around the axis of the hole while rotating with its own axis and feeds in the axial direction in the helical milling process. Based on the cutting mechanism of the helical milling process， considering the effect of the side edges and bottom edges on the major cutting during the feed process and the anisotropic characteristics of the composite material， a cutting force analytical model was established in the helical milling of carbon fiber reinforced plastics (CFRP). According to the composite material helical milling test data under the full factor condition， the data fitting method was used to identify the bottom edge cutting force coefficient， and the instantaneous cutting force method was used to identify the side edge cutting force coefficient. The results showed that the simulated cutting force can better fit the experimental value.

Key words: helical milling, CFRP, cutting force, instantaneous cutting force coefficient, cutting experiment

中图分类号:

TH164

王海艳，王健宇，陶克新. 碳纤维复合材料螺旋铣孔瞬时切削力系数识别[J]. 东北大学学报:自然科学版, 2020, 41(10): 1432-1437.

WANG Hai-yan， WANG Jian-yu， TAO Ke-xin. Identification of Instantaneous Cutting Force Coefficients for Helical Milling of Carbon Fiber Composite Materials[J]. Journal of Northeastern University Natural Science, 2020, 41(10): 1432-1437.

参考文献

[1]Tian Y，Liu Y，Wang F，et al.Modeling and analyses of helical milling process［J］.International Journal of Advanced Manufacturing Technology，2017，l90:1003-1022.
[2]Shang S，Qin X D，Li J H，et al.Modeling of cutting forces and researching calibration method in helical milling［J］.International Journal of Advanced Manufacturing Technology，2018，94:2949-2960.
[3]Wang H Y，Qin X D，Ren C Z，et al.Prediction of cutting forces in helical milling process［J］.International Journal of Advanced Manufacturing Technology，2011，58:849-859.
[4]Liu C，Wang G F，Dargusch M S.Modeling，simulation and experimental investigation of cutting forces during helical milling operations［J］.International Journal of Advanced Manufacturing Technology，2012，63:839-850.
[5]Li Z Q，Liu Q，Ming X，et al.Cutting force prediction and analytical solution of regenerative chatter stability for helical milling operation［J］.International Journal of Advanced Manufacturing Technology，2014，73:433-442.
[6]Rey P A，LeDref L，Senatore J，et al.Modeling of cutting forces in orbital drilling of titanium alloy Ti-6Al-4V［J］.International Journal of Machine Tools and Manufacturing，2016，106:75-88.
[7]Gradisek J，Kalveram M，Weinert K.Mechanistic identification of specific force coefficients for a general end mill［J］.International Journal of Machine Tools and Manufacturing，2004，44:401-414.
[8]王博，黎柏春，杨建宇，等.面向球头铣刀多轴铣削加工的铣削力系数辨识［J］.东北大学学报(自然科学版)，2018，39(11):1630-1635.(Wang Bo，Li Bai-chun，Yang Jian-yu，et al.Milling force coefficient identification for multi-axis and ball end milling cutter［J］.Journal of Northeastern University (Natural Science)，2018，39(11):1630-1635.)
[9] Budak E，Altinas Y，Armarego E J A.Prediction of milling force coefficients from orthogonal cutting data［J］.Journal of Manufacturing Science and Engineering，1996，118:216-224.
[10]Gonzalo O，Jauregi H，Uriarte L G，et al.Prediction of specific force coefficients from a FEM cutting model［J］.International Journal of Advanced Manufacturing Technology，2009，43:348-356.
[11]Gonzalo O，Beristain J，Jauregi H，et al.A method for the identification of the specific force coefficients for mechanistic milling simulation［J］.International Journal of Machine Tools and Manufacturing，2010，50:765-774.
[12]Karpat Y，Bahtiyar O，Deger B.Mechanistic force modeling for milling of unidirectional carbon fiber reinforced polymer laminates［J］.International Journal of Machine Tools and Manufacture，2012，56:79-93.
[13]He Y L，Ahmad J S，Zhu S W，et al.Cutting force analysis considering edge effects in the milling of carbon fiber reinforced polymer composite［J］.Journal of Materials Processing Technology，2020，279:1-12.
[14]Wang H Y，Qin X D，Li H，et al.Analysis of cutting forces in helical milling of carbon fiber-reinforced plastics［J］.Institution of Mechanical Engineers Journal of Engineering Manufacture，2013，227(1):62-74.
[15]Wan M，Lu M S，Zhang W H，et al.A new ternary-mechanism model for the prediction of cutting forces in flat end milling［J］.International Journal of Machine Tool and Manufacture，2012，57:34-45.
[16]Denkena B，Boehnke D，Dege J H.Helical milling of CFRP-titanium layer compounds［J］.CIRP Journal of Manufacturing Science and Technology，2008，1:64-69.
[15]关守平，房少纯.一种新型的区间-粒子群优化算法［J］.东北大学学报(自然科学版)，2012，33(10):1381-1384.(Guan Shou-ping，Fang Shao-chun.A new interval particle swarm optimization algorithm［J］.Journal of Northeastern University(Natural Science)，2012，33(10):1381-1384.)

碳纤维复合材料螺旋铣孔瞬时切削力系数识别

Identification of Instantaneous Cutting Force Coefficients for Helical Milling of Carbon Fiber Composite Materials

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 14

编辑推荐

Metrics

本文评价

[1]	王海艳，金天，周秩同，付麒麟. 碳纤维增强复合材料螺旋铣孔的临界轴向力模型[J]. 东北大学学报（自然科学版）, 2022, 43(2): 214-220.
[2]	方锐，邹平，段经伟，张硕. 微织构刀具三维超声振动车削304不锈钢研究[J]. 东北大学学报（自然科学版）, 2022, 43(12): 1761-1768.
[3]	许家忠，赵辉，付天宇，张成东. 感应加热CFRP温度控制算法[J]. 东北大学学报（自然科学版）, 2022, 43(1): 17-24.
[4]	丁鹏飞，王昌利，黄贤振，李禹雄. 细长轴车削加工误差可靠性灵敏度分析[J]. 东北大学学报（自然科学版）, 2021, 42(5): 693-699.
[5]	王海艳，陶克新，金天. 球头铣刀螺旋铣孔材料去除及孔形成过程分析[J]. 东北大学学报:自然科学版, 2020, 41(11): 1602-1608.
[6]	黎柏春，王振宇，张斌，王宛山. 球头铣刀切削刃存在差异的切削力系数辨识[J]. 东北大学学报:自然科学版, 2019, 40(9): 1316-1322.
[7]	张荣闯，黎柏春，张景强. 圆柱齿轮滚齿切削力的预测[J]. 东北大学学报:自然科学版, 2019, 40(7): 980-985.
[8]	张宝，赵春雨，闻邦椿. 机床动态切削力测定试验与时间序列模型预测[J]. 东北大学学报:自然科学版, 2019, 40(4): 521-526.
[9]	杨佳，王连广，侯雯峪. 内嵌CFRP板条加固损伤预应力混凝土梁抗弯性能[J]. 东北大学学报:自然科学版, 2019, 40(4): 590-595.
[10]	刘宇，王振宇，杨慧刚，张义民. 车削颤振时变可靠性预测[J]. 东北大学学报:自然科学版, 2017, 38(5): 684-689.
[11]	黄贤振，曹辉，张义民. 基于蒙特卡罗方法的直角切削切削力概率特性分析[J]. 东北大学学报:自然科学版, 2015, 36(2): 254-258.
[12]	马廉洁，李琛，曹小兵，巩亚东. 基于GA和DEFORM的陶瓷材料切削力数值模拟[J]. 东北大学学报:自然科学版, 2014, 35(12): 1773-1777.
[13]	郝春水;吴凤春. 稀土硬质合金刀片切削性能[J]. 东北大学学报:自然科学版, 1994, 15(5): 4--.
[14]	郝春水;吴凤春. 稀土硬质合金刀片切削性能[J]. 东北大学学报:自然科学版, 1994, 15(5): 4--.