断裂面缺损定量分析及其对连杆强度的影响

doi:10.12068/j.issn.1005-3026.2019.01.016

东北大学学报:自然科学版 ›› 2019, Vol. 40 ›› Issue (1): 82-87.DOI: 10.12068/j.issn.1005-3026.2019.01.016

断裂面缺损定量分析及其对连杆强度的影响

石舟^1,2，寇淑清^1,2

(1. 吉林大学辊锻工艺研究所，吉林长春130025; 2. 吉林大学材料科学与工程学院，吉林长春130025)

收稿日期:2017-10-27 修回日期:2017-10-27 出版日期:2019-01-15 发布日期:2019-01-28
通讯作者: 石舟
作者简介:石舟(1989-)，女，山东泰安人，吉林大学博士研究生; 寇淑清(1962-)，女，黑龙江肇源人，吉林大学教授，博士生导师.
基金资助:
国家重点研发计划项目(2016YFD0701102).

Quantitative Analysis of Fracture Surface Defect and Its Effect on Strength of Connecting Rod

SHI Zhou^1,2， KOU Shu-qing^1,2

1. Roll Forging Research Institute， Jilin University， Changchun 130025， China; 2. College of Materials Science and Engineering， Jilin University， Changchun 130025， China.

Received:2017-10-27 Revised:2017-10-27 Online:2019-01-15 Published:2019-01-28
Contact: KOU Shu-qing
About author:-
Supported by:
-

摘要/Abstract

摘要： 借助连杆裂解实验获得断裂接合面，利用逆向工程重构断裂面，建立带缺损的连杆模型，实现连杆断裂面缺损定量描述.探究不同尺寸、不同位置的缺损对连杆强度的影响，以此为依据制定加工中相关技术标准.通过模拟得出:随缺损尺寸增加，连杆承受的应力逐渐增加，连杆强度降低.缺损面积越大，其对连杆应力的影响越显著.同尺寸缺损当其位于接合面内部时，连杆的等效应力大于其位于接合面边缘，即内部缺损带来的危害高于边缘缺损.为保证连杆强度，缺损尺寸应满足:边缘缺损，当1.5mm＜b＜2.5mm时，a≤-1.125b+5.0875;面内缺损，当1.4mm＜b＜2.1mm时，a≤-1.143b+4.8.

关键词: 连杆裂解, 断裂面, 缺损, 定量描述, 强度, 控制标准

Abstract: The fracture joint surface was obtained by the fracture-split test and the fracture surface was reconstructed by reverse engineering. The connecting rod model with defect was built. The quantitative description of the fracture surface defect was realized. The effects of fracture surface defect of different sizes and positions on the strength of the connecting rod were explored， and the control standard of the relevant dimension in the processing process was formulated. The rules were obtained: with the defect size increasing， the stress of the connecting rod increases gradually and the strength of the connecting rod decreases. When the defect area is larger， the influence on the stress of the connecting rod becomes more significant. The stress of the connecting rod is greater when defect is inside the joint surface than that at the edge of the joint surface. In order to ensure the strength of the connecting rod， the defect size should meet: defect on edge， when 1.5mm＜b＜2.5mm， a≤-1.125b+5.0875; in-plane defect， when 1.4mm＜b＜2.1mm， a≤-1.143b+4.8.

Key words: connecting rod fracture-split, fracture surface, defect, quantitative description, strength, control standard

中图分类号:

TK406

石舟，寇淑清. 断裂面缺损定量分析及其对连杆强度的影响[J]. 东北大学学报:自然科学版, 2019, 40(1): 82-87.

SHI Zhou， KOU Shu-qing. Quantitative Analysis of Fracture Surface Defect and Its Effect on Strength of Connecting Rod[J]. Journal of Northeastern University Natural Science, 2019, 40(1): 82-87.

参考文献

[1]Wang B，Li M，Yang Y，et al.Note:double-beveled multilayer stagger-split die for a large volume high-pressure apparatus［J］.Review of Scientific Instruments，2015，86(8):086106.
[2]杨宏宇.连杆断裂剖分过程数值模拟及主要裂解缺陷分析［D］.长春:吉林大学，2014.(Yang Hong-yu.Numerical simulation of connecting rod fracture process and analysis on main fracture splitting defects［D］.Changchun:Jilin University，2014.)
[3]Fukuda S，Eto H.Development of fracture splitting connecting rod［J］.Jsae Review，2002，23(1):101-104.
[4]Yang H，Kou S，Gao W，et al.Analysis on technology and defects of fracture splitting of automobile engine connecting rod［J］.Proceedings of the Institution of Mechanical Engineers，Part B:Journal of Engineering Manufacture，2015，229(9):1603-1613.
[5]Gu Z，Yang S，Ku S，et al.Fracture splitting technology of automobile engine connecting rod［J］.The International Journal of Advanced Manufacturing Technology，2005，25(9):883-887.
[6]寇淑清，杨宏宇，赵勇，等.裂解连杆断裂面三维重构与缺损尺寸分析［J］.东北大学学报(自然科学版)，2014，35(4):574-578.(Kou Shu-qing，Yang Hong-yu，Zhao Yong，et al.3D reconstruction and defect dimension analysis of fracture surface for fracture splitting connecting rods［J］.Journal of Northeastern University(Natural Science)，2014，35(4):574-578.)
[7]Shi Z，Kou S Q.Inverse reconstruction of fracture splitting connecting rod and its strength and fatigue life［J］.Journal of Failure Analysis and Prevention，2018，18(3):619-627.
[8]Wang B，Li M，Yang Y，et al.Numerical simulation of multilayer stagger-split die and experiment on the bearing capacity［J］.High Pressure Research，2015，35(4):388-395.
[9]Hughes T J R，Cottrell J A，Bazilevs Y.Isogeometric analysis:CAD，finite elements，NURBS，exact geometry and mesh refinement［J］.Computer Methods in Applied Mechanics and Engineering，2005，194(39):4135-4195.
[10]Keita O，Hedhli T，Bessrour J.Model for dynamic behavior of the crankshaft of an air cooled diesel engine subjected to severe functioning［J］.International Journal of Automotive Technology，2014，15(5):823-833.(上接第57页)
[7]Mei D，Xing F，Wen M，et al.Numerical simulation of mixed convection heat transfer of galvanized steel sheets in the vertical alloying furnace ［J］.Applied Thermal Engineering，2016，93:500-508.
[8]孙用军.辽西钒钛磁铁矿直接提钒焙烧竖炉气固传热数值计算［D］.沈阳:东北大学，2015.(Sun Yong-jun.Numerical study of gas-solid heat transfer on roasting shaft furnace for vanadium titano-magnetite in western Liaoning province［D］.Shenyang:Northeastern University，2015.)
[9]Mahmoudi Y，Maerefat M.Analytical investigation of heat transfer enhancement in a channel partially filled with a porous material under local thermal non-equilibrium condition［J］.International Journal of Thermal Sciences，2011，50(12):2386-2401.
[10]Nakayama A，Kuwahara F，Sugiyama M，et al.A two-energy equation model for conduction and convection in porous media［J］.International Journal of Heat and Mass Transfer，2001，44(22):4375-4379.
[11]王国胜，董辉，蔡九菊.球团竖炉热工过程解析与模拟［J］.钢铁，2004，39(4):60-63.(Wang Guo-sheng，Dong Hui，Cai Jiu-ju.Analysis and simulation of thermo process in pelletizing shaft furnace［J］.Iron and Steel，2004，39(4):60-63.)
[12]邵颖聪.辽西钒钛磁铁矿直接提钒焙烧浸出工艺及竖炉热工过程研究［D］.沈阳:东北大学，2015.(Shao Ying-cong.Experimental study on roasting and leaching process of compact extracting vanadium process and analysis on thermo process in roasting shaft furnace［D］.Shenyang:Northeastern University，2015.)

[1]	虞力，孟庆有，袁致涛，徐新阳. 基于高强度调浆的钛铁矿浮选研究[J]. 东北大学学报（自然科学版）, 2023, 44(4): 573-580.
[2]	闫佳祺，贾建锋，赵若男，连粤丰. 高承诺型人力资源管理实践对突破式创新的影响[J]. 东北大学学报（自然科学版）, 2022, 43(8): 1209-1216.
[3]	贾建锋，赵洋，刘秋余. 积极追随特质对员工创新行为的影响——感知的人力资源管理强度与工作嵌入的作用[J]. 东北大学学报（自然科学版）, 2022, 43(6): 905-912.
[4]	孙浩，陈帅军，金爱兵，朱东风. 含裂隙类岩石试样单轴抗压强度特征及裂纹演化规律[J]. 东北大学学报（自然科学版）, 2022, 43(3): 404-413.
[5]	张玉，刘伯权，吴涛，陈旭. 变形钢筋与高强轻骨料混凝土的黏结-滑移性能[J]. 东北大学学报（自然科学版）, 2022, 43(2): 274-282.
[6]	彭志雄，曾亚武. 基于裂纹扩展作用下的岩石损伤力学模型[J]. 东北大学学报（自然科学版）, 2022, 43(12): 1784-1791.
[7]	陈猛，曹宇新，王瑜婷. 工程水泥基复合材料高温损伤超声特性[J]. 东北大学学报（自然科学版）, 2022, 43(11): 1638-1643.
[8]	许江波，费东阳，孙浩珲，崔易仑. 节理千枚岩能量传递与动力学特性[J]. 东北大学学报（自然科学版）, 2021, 42(7): 986-995.
[9]	张晶，任凤玉，何荣兴，欧阳治华. 包含岩石临界状态的Mohr-Wedge准则适用性研究[J]. 东北大学学报（自然科学版）, 2021, 42(4): 567-575.
[10]	张鹏，高谦，温震江，张涛. 充填体强度影响因素及组合预测模型[J]. 东北大学学报（自然科学版）, 2021, 42(2): 232-241.
[11]	王述红，尹宏，张泽，魏崴. 考虑三维形貌参数的结构面峰值剪切强度预测新模型[J]. 东北大学学报（自然科学版）, 2021, 42(11): 1609-1617.
[12]	周成，刘文鹏，叶其斌，王昭东. 亚稳奥氏体对高强度海洋工程用钢力学性能的影响[J]. 东北大学学报（自然科学版）, 2021, 42(10): 1400-1406.
[13]	于洪雯，安龙，李元辉，高传波. 微波辐射对变粒岩孔隙结构及抗拉强度的影响[J]. 东北大学学报（自然科学版）, 2021, 42(10): 1451-1458.
[14]	黄少平，晏鄂川，陈前，尹晓萌. 干湿循环与持续浸泡下老黏土强度与变形特性变化[J]. 东北大学学报:自然科学版, 2020, 41(5): 649-654.
[15]	丁明超，张元良，咸宏伟，王金龙. 基于微观划痕的疲劳强度预测[J]. 东北大学学报:自然科学版, 2020, 41(5): 693-699.

断裂面缺损定量分析及其对连杆强度的影响

Quantitative Analysis of Fracture Surface Defect and Its Effect on Strength of Connecting Rod

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价